Dell PowerVault DR4100 Owner'S Manual Download Page 19

Page: 19 / 122

Menu Item

Description

Execute Disable

Allows you enable or disable execute disable memory protection technology. By default, the
Execute Disable option is set to Enabled.

Logical Processor
Idling

Allows you to enable or disable the OS capability to put logical processors in the idling state in
order to reduce power consumption. By default, the option is set to Disabled.

Number of Cores per
Processor

Allows you to control the number of enabled cores in each processor. By default, the Number
of Cores per Processor option is set to All.

Processor 64-bit
Support

Specifies if the processor(s) support 64-bit extensions.

Processor Core
Speed

Displays the maximum core frequency of the processor.

Processor Bus Speed Displays the bus speed of the processors.

NOTE: The processor bus speed option displays only when both the processors are
installed.

Processor 1

NOTE: The following settings are displayed for each processor installed in the system.

Family-Model-
Stepping

Displays the family, model and stepping of the processor as defined by Intel.

Brand

Displays the brand name reported by the processor.

Level 2 Cache

Displays the total L2 cache.

Level 3 Cache

Displays the total L3 cache.

Number of Cores

Displays the number of cores per processor.

Boot Settings Screen

Menu Item

Description

Boot Mode

Allows you to set the boot mode of the system.

CAUTION: Switching the boot mode may prevent the system from booting if the operating
system is not installed in the same boot mode.

By default, the Boot Mode option is set to BIOS.

Boot Sequence Retry Allows you to enable or disable the boot sequence retry feature. If this field is enabled and the

system fails to boot, the system reattempts the boot sequence after 30 seconds. By default, the
Boot Sequence Retry option is set to Disabled.

BIOS Boot Settings

Allows you to enable or disable BIOS Boot options.

NOTE: This option is enabled only if the boot mode is BIOS.

One-Time Boot

Allows you to enable or disable a one-time boot from a selected device.

Summary of Contents for PowerVault DR4100



























































































































Search results

Summary of Contents for PowerVault DR4100

Reviews:

Related manuals for PowerVault DR4100

Brands by name

Popular brands

Dell PowerVault DR4100, Owner'S Manual

Search results

Summary of Contents for PowerVault DR4100

Reviews:

Related manuals for PowerVault DR4100

Brands by name

Popular brands