Dell OptiPlex 5040 Series Owner'S Manual Download Page 53 | Manualshive

Page: 53 / 63

background image

Option

Description

NOTE: This feature does not work if you turn off your computer using
the switch on a power strip or surge protector or if

Auto Power is set to

disabled

.

Deep Sleep Control

Allows you to define the controls when Deep Sleep is enabled.
• Disabled
• Enabled in S5 only
• Enabled in S4 and S5

This option is Disabled by default.

Fan Control Override

Allows you to determine the speed of the system fan. When this option is
enabled, the system fan runs at the maximum speed. This option is disabled
by default.

USB Wake Support

Allows you to enable the USB devices to wake the computer from standby
mode.

Wake on LAN/WWAN

This option allows the computer to power up from the off state when
triggered by a special LAN signal. This feature only works when the
computer is connected to AC power supply.
•

Disabled

- Does not allows the system to power on by special LAN

signals when it receives a wake-up signal from the LAN or wireless LAN.

•

LAN

or

WLAN

- Allows the system to be powered on by special LAN or

wireless LAN signals.

•

LAN Only

- Allows the system to be powered on by special LAN signals.

•

LAN with PXE Boot

- A wakeup packet sent to the system in either the

S4 or S5 state, that will cause the system to wake-up and immediately

boot to PXE.

•

WLAN Only

- Allows the system to be powered on by special WLAN

signals.

This option is Disabled by default.

Block Sleep

Allows you to block entering to sleep (S3 state) in OS environment. This

option is disabled by default.

Intel Ready Mode

Allows you to enable the capability of Intel Ready Mode Technology. This

option is disabled by default.

Table 27. POST behavior

Option

Description

Numlock LED

Allows you to enable or disable the Numlock feature when your computer

starts. This option is enabled by default.

MEBx Hotkey

Allows you to specify whether the MEBx Hotkey function should be enabled

when the system boots. This option is enabled by default.

Keyboard Errors

Allows you to enable or disable the keyboard error reporting when the

computer starts. This option is enabled by default.

Fast Boot

This option can speed up the boot process by bypassing some compatibility

steps:
• Minimal — The system boots quickly, unless the BIOS has been updated,

memory changed, or the previous POST did not complete.

• Thorough — The system does not skip any steps in the boot process.

53

«
...
51
52
53
54
55
...
»

Summary of Contents for OptiPlex 5040 Series
































































Reviews:

No comments

Related manuals for OptiPlex 5040 Series

Brand: Igel Pages: 2

Brand: iDOT Pages: 66

PT-970 A Series

Brand: Contec Pages: 77

Literail Workstation 6 Person

Brand: Jason.L Pages: 4

DECstaion 5000 240

Brand: Digital Equipment Pages: 62

Brand: Elo TouchSystems Pages: 3

Brand: DT Research Pages: 2

Rosemount TankRadar SCC 5320

Brand: Emerson Pages: 4

Brand: Emerson Pages: 108

Brand: Dell Pages: 165

DGX Station A100

Brand: Nvidia Pages: 72

MT EU Business PC

Brand: HP Pages: 3

Brand: HP Pages: 2

m9260f Pavilion Elite

Brand: HP Pages: 1

M9402f - pavilion - elite

Brand: HP Pages: 2

m9260f Pavilion Elite

Brand: HP Pages: 2

Brand: HP Pages: 4

OMEN Obelisk 873

Brand: HP Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands