background image

Back to Contents Page

  

 

 Speaker  

Dell™ Latitude™ D430 

 

 

 

 

1.

Follow the instructions in 

"Before You Begin" on page 7

 

 

 

  

2.

Remove any installed PC Cards from the PC Card slot.  
 

 

  

3.

Remove any installed memory modules or Mini PCI cards (see 

Memory

 and 

Mini-Cards

).  

 

 

  

4.

Remove the hard drive (see 

Hard Drive

).  

 

 

  

5.

Remove the hinge cover (see 

Hinge Cover

).  

 

 

  

6.

Remove the keyboard (see 

Keyboard

).  

 

 

  

7.

Remove the internal card with Bluetooth

® 

wireless technology (see 

Internal Card With Bluetooth

® 

Wireless Technology

).  

 

 

  

8.

Remove the display assembly (see 

Display Assembly

).  

 

 

  

9.

Remove the palm rest (see 

Palm Rest

).  

 

 

  

10.

Turn the palm rest upside down and disconnect the speaker connector from the system board.  
 

 

  

11.

Remove the two M2 x 3-mm speaker screws from the computer base.  
 

  

Back to Contents Page

 

 

 

 

CAUTION: 

Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide. 

 

NOTICE: 

To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such 

as the back panel) on the computer. 

1  speaker 

2  M2 x 3-mm speaker screws (2) 

3  speaker cables routing 

4  bottom of palm rest 

 

 

 

 

 

 

 

 

Summary of Contents for Latitude D430






































Reviews: