Dell Latitude D430 Service Manual Download Page 6

Page: 6 / 37

Back to Contents Page

Internal Card With Bluetooth

Wireless Technology

Dell™ Latitude™ D430

If you ordered an internal card with Bluetooth wireless technology with your computer, it is already installed.

Follow the procedures in

"Before You Begin" on page 7

Remove the hinge cover (see

Hinge Cover

Remove the keyboard (see

Keyboard

Remove the M2 x 3-mm screw from the card holder and lay the holder aside.

Lift the card away from the aligning pin.

Disconnect the card cable connector from the card.

Back to Contents Page

CAUTION:

Before performing the following procedures, read the safety instructions in your Product Information Guide.

NOTICE:

To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching a connector on the back panel of

the computer.

NOTICE:

To prevent damage to the system board, remove the main battery before you service the computer.

1 internal card with Bluetooth wireless

technology

2 card cable

connector

3 M2 x 3-mm

screw

4 card holder

5 aligning pin

NOTICE:

Be careful when removing the card to avoid damaging the card, card cable, or surrounding components.

Summary of Contents for Latitude D430






































Search results

Summary of Contents for Latitude D430

Reviews:

Related manuals for Latitude D430

Brands by name

Popular brands

Dell Latitude D430, Service Manual

Search results

Summary of Contents for Latitude D430

Reviews:

Related manuals for Latitude D430

Brands by name

Popular brands