Dell Latitude D430 Service Manual Download Page 13

Page: 13 / 37

Align the card with the connector at a 45-degree angle, and press the card into the connector until you feel a click.

Connect the white antenna cable with the black stripe to the connector on the card marked with a white triangle; connect the black antenna

cable with the white stripe to the connector on the card marked with a black triangle.

Subscriber Identity Module (SIM) Card

Slide the SIM card out of the SIM card slot with the cut-off corner of the card facing toward the back of the computer.

NOTE:

Cable routing for the Mobile Broadband card may vary.

1 Mobile Broadband card 2 system board connector

NOTE:

For more specific information about which cable to connect to which connector, see the documentation that came with your Mobile Broadband

card.

NOTICE:

To protect the SIM card from electrostatic discharge (ESD), do not touch the SIM card connector. Also, take care when removing the card to

slide the card completely out of the metal tabs before lifting the card out of the slot. The card is brittle and may easily break otherwise.

NOTE:

The SIM card is located in the battery bay. You must remove the main battery before you can access the SIM card.

Summary of Contents for Latitude D430






































Search results

Summary of Contents for Latitude D430

Reviews:

Related manuals for Latitude D430

Brands by name

Popular brands

Dell Latitude D430, Service Manual

Search results

Summary of Contents for Latitude D430

Reviews:

Related manuals for Latitude D430

Brands by name

Popular brands