background image

Back to Contents Page

  

 

 Fan  

Dell™ Latitude™ D430 

 

 

 

 

1.

Follow the instructions in 

"Before You Begin" on page 7

 

 

 

  

2.

Remove any installed PC Cards from the PC Card slot.  
 

 

  

3.

Remove any installed memory modules or Mini PCI cards (see 

Memory

 and 

Mini-Cards

).  

 

 

  

4.

Remove the hard drive (see 

Hard Drive

).  

 

 

  

5.

Remove the hinge cover (see 

Hinge Cover

).  

 

 

  

6.

Remove the keyboard (see 

Keyboard

).  

 

 

  

7.

Remove the internal card with Bluetooth

® 

wireless technology (see 

Internal Card With Bluetooth

® 

Wireless Technology

).  

 

 

  

8.

Remove the display assembly (see 

Display Assembly

).  

 

 

  

9.

Remove the palm rest (see 

Palm Rest

) and lay it aside.  

 

 

  

10.

Remove the system board (see 

System Board

) and remove the fan connector from the top of the system board.  

 

 

  

11.

Turn the system board upside down.  
 

 

 

12.

Loosen the three captive screws from the fan, and lift the fan away from bottom of the system board.  
 

  

Back to Contents Page

 

 

 

 

CAUTION: 

Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide. 

 

CAUTION: 

To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of 

your computer's electronic components. You can do so by touching an unpainted metal surface. 

 

NOTICE: 

Handle components and cards by their edges, and avoid touching pins and contacts. 

 

NOTICE: 

Ensure that you have moved any cables out of the way before you lift away the fan. 

1  modem cable  2  captive screws (3) 

3  bottom of system board 

4  fan assembly  5  fan connector on top of the system board 

 

 

 

 

Summary of Contents for Latitude D430






































Reviews: