Dell Latitude D430 Service Manual Download Page 12

Page: 12 / 37

Mobile Broadband (WWAN) Cards

If you ordered a Mobile Broadband card with your computer, the card is already installed.

If a Mobile Broadband card is not already installed, go to step 5. If you are replacing a Mobile Broadband card, remove the existing card:

Disconnect the Mobile Broadband card from any attached cables.

Use your fingertips to carefully spread apart the metal securing tabs until the card pops up slightly.

Slide and lift the Mobile Broadband card out of its connector.

To install a Mobile Broadband card:

Move any antenna cables out of the way to make space for the card.

NOTE:

Mobile Broadband cards may not be available in all regions.

CAUTION:

Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.

1 antenna wires (2) 2 Mobile Broadband card

1 Mobile Broadband card 2 metal securing tabs (2)

NOTICE:

To prevent damage to the connector, do not use tools to spread the securing clips.

NOTICE:

The connectors are keyed to ensure correct insertion. If you feel resistance, check the connectors and realign the card.

NOTE:

Do not insert a WLAN card into the Mobile Broadband card slot.

NOTICE:

The Mobile Broadband card may have one or two connectors, depending on the type of card you ordered.

NOTICE:

To avoid damaging the Mobile Broadband card, never place cables on top of or under the card and ensure that you route the cables properly.

Summary of Contents for Latitude D430






































Search results

Summary of Contents for Latitude D430

Reviews:

Related manuals for Latitude D430

Brands by name

Popular brands

Dell Latitude D430, Service Manual

Search results

Summary of Contents for Latitude D430

Reviews:

Related manuals for Latitude D430

Brands by name

Popular brands