Dell Inspiron 1300 Service Manual Download | Manualshive

Page: 17 / 44

background image

6.

Press in both sides of the top flex-cable connector, and pull the top flex-cable connector away from the display connector.

7.

Use the pull-tab to disconnect the bottom flex-cable connector from the inverter connector.

Installing the Display Panel

1.

Connect the top flex-cable connector to the display panel connector.

2.

Connect the bottom flex-cable connector to the inverter connector.

3.

Lay the display panel into the top cover.

4.

Replace the eight M2 x 3-mm screws that secure the display panel to the top cover.

5.

Route the display-feed flex cable so that it rests in the notch located in the bottom edge of the top cover.

6.

Replace the display bezel.

Back to Contents Page

1

display panel

2

top cover

3

M2 x 3-mm screws (8)

1 inverter connector 2 pull-tab on bottom flex-cable connector 3 top flex-cable connector

4 display connector

«
...
15
16
17
18
19
...
»

Summary of Contents for Inspiron 1300













































Reviews:

No comments

Related manuals for Inspiron 1300

Brand: Gateway Pages: 81

Brand: Medion Pages: 100

Aspire 5 A515-56

Brand: Acer Pages: 87

Aspire 7735ZG Series

Brand: Acer Pages: 13

Aspire 7535 Series

Brand: Acer Pages: 220

Brand: Acer Pages: 9

TravelMate 5335

Brand: Acer Pages: 313

TravelMate 5740

Brand: Acer Pages: 314

Extensa 5430 Series

Brand: Acer Pages: 176

MX6440 - Notebook Computer

Brand: Gateway Pages: 1

Compaq Mini Series

Brand: HP Pages: 52

Brand: HP Pages: 3

Compaq Mini 110

Brand: HP Pages: 6

Brand: HP Pages: 15

Brand: HP Pages: 67

Compaq Mini CQ10-410SF

Brand: HP Pages: 52

Compaq Mini 210

Brand: HP Pages: 67

Compaq Mini 110

Brand: HP Pages: 93

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands