Dell Inspiron 1300 Service Manual Download | Manualshive

Page: 38 / 44

background image

Installing the Microprocessor Thermal-Cooling Assembly

1.

Lower the microprocessor thermal-cooling assembly into place on top of the microprocessor, aligning the numbered screws, labeled "1" through "4,"
with the numbers on the fan assembly, and the arrow on the pull-strap pointing toward the outside edge of the system board.

2.

Tighten the four captive screws, labeled "1" through "4," in consecutive order.

3.

Replace the thermal-cooling/microprocessor cover and tighten the screws.

Back to Contents Page

NOTICE:

Before you install the replacement microprocessor thermal-cooling assembly, remove the mylar that covers the thermal grease on the

assembly.

«
...
36
37
38
39
40
...
»

Summary of Contents for Inspiron 1300













































Reviews:

No comments

Related manuals for Inspiron 1300

CELSIUS Mobile A

Brand: Fujitsu Siemens Computers Pages: 95

Brand: i-Life Pages: 12

CompBook Excelance-OHD

Brand: iBall Pages: 18

StepNote VA2001T

Brand: Everex Pages: 1

AcerNote Light 370

Brand: Acer Pages: 16

Brand: Acer Pages: 28

Acer TravelMate 3300 Series

Brand: Acer Pages: 75

Brand: Acer Pages: 88

AcerNote Light 370

Brand: Acer Pages: 3

Aspire 1360 Series

Brand: Acer Pages: 143

Brand: Acer Pages: 11

Brand: Acer Pages: 79

AS7315-302G25Mn

Brand: Acer Pages: 200

AS4810T- 354G32Mn LX.PBA0X.075

Brand: Acer Pages: 148

Brand: Acer Pages: 69

Brand: Acer Pages: 224

Brand: Acer Pages: 100

Brand: Acer Pages: 92

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands