Dell Inspiron 1300 Service Manual Download

Page: 34 / 44

Installing the System Board

Insert the video connector on the replacement system board through the side of the base plastics.

Replace the five M2.5 x 5-mm screws that secure the system board to the base plastics.

Reconnect the speakers. See

Installing the Speakers

Replace the modem removed from the system board. See

Replacing the Modem

Replace the palm rest. See

Removing the Palm Rest

and follow the procedure in reverse order

Replace the display assembly. See

Removing the Display Assembly

and follow the procedure in reverse order.

Replace the keyboard. See

Replacing the Keyboard

Replace the microprocessor. See

Installing the Microprocessor Module

Replace the microprocessor thermal-cooling assembly. See

Installing the Microprocessor Thermal- Cooling Assembly

10.

Replace the Mini PCI card that you removed from the old system board. See

Installing the Mini PCI Card

11.

Replace the memory module that you removed from the old system board. See

Replacing the Memory Module

12.

Replace the optical drive. See

Installing the Optical Drive

13.

Replace the hard drive. See

Installing the Hard Drive

14.

Insert the battery into the battery bay. See

Replacing the Battery

15.

Connect the AC adapter to the computer and to an electrical outlet.

16.

Turn on the computer.

17.

Insert the CD that accompanied the replacement system board into the appropriate drive. Follow the instructions on the screen.

Back to Contents Page

M2.5 x 5-mm screws (5)

NOTICE:

Before you replace the microprocessor thermal-cooling assembly, wipe the thermal grease off of the assembly with a clean paper towel.

Squeeze the contents of the thermal grease packet (provided with the kit) onto the microprocessor thermal-cooling assembly.

NOTICE:

Before turning on the computer, replace all screws and ensure that no stray screws remain inside the computer. Failure to do so may result in

damage to the computer.

NOTE:

After replacing the system board, enter the computer Service Tag into the BIOS of the replacement system board.

Summary of Contents for Inspiron 1300













































Search results

Summary of Contents for Inspiron 1300

Reviews:

Related manuals for Inspiron 1300

Brands by name

Popular brands

Dell Inspiron 1300, Service Manual

Search results

Summary of Contents for Inspiron 1300

Reviews:

Related manuals for Inspiron 1300

Brands by name

Popular brands