background image

Back to Contents Page

  

 

 Microprocessor Module  

Dell™ Inspiron™ 1300/B120/B130  Service Manual

 

  

Removing the Microprocessor Module 

 

  

Installing the Microprocessor Module 

 

 

 

Removing the Microprocessor Module  

 

 

 

 

 

 

1.

Follow the instructions in 

Before Working Inside Your Computer

.  

 

 

  

2.

Turn over the computer.  
 

 

  

3.

Remove the microprocessor thermal-cooling assembly. See 

Removing the Microprocessor Thermal-Cooling Assembly

.  

 

 

 

4.

To loosen the ZIF socket, use a small, flat-blade screwdriver and rotate the ZIF-socket cam screw counterclockwise until it comes to the cam stop.  
 

The ZIF-socket cam screw secures the microprocessor to the system board. Take note of the arrow on the ZIF-socket cam screw. 

  

 

 

5.

Use a microprocessor extraction tool to remove the microprocessor module.  
 

 

Installing the Microprocessor Module  

 

CAUTION: 

Before performing the following procedures, read the safety instructions in the 

Product Information Guide

 

CAUTION: 

To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of 

your computer's electronic components. You can do so by touching an unpainted metal surface.

 

NOTICE: 

Press and hold the microprocessor down by applying slight pressure to the center of the microprocessor while turning the cam screw to 

prevent intermittent contact between the cam screw and microprocessor.

 

NOTICE: 

To avoid damage to the microprocessor, hold the screwdriver so that it is perpendicular to the microprocessor when turning the cam screw.

 

NOTICE: 

When removing the microprocessor module, pull the module straight up. Be careful not to bend the pins on the microprocessor module.

1  ZIF-socket cam screw 

2  ZIF-socket 

3  pin-1 corner of microprocessor 

 

NOTICE: 

Ensure that the cam lock is in the fully open position before seating the microprocessor module. Seating the microprocessor module properly in 

the ZIF socket does not require force.

 

NOTICE: 

A microprocessor module that is not properly seated can result in an intermittent connection or permanent damage to the microprocessor and 

ZIF socket.

Summary of Contents for Inspiron 1300













































Reviews: