manualshive.com logo in svg

Dell EMC PowerEdge 14G Series, Manual

Share
Download
Dell EMC PowerEdge 14G Series Manual Download Page 21

 

Chapter 4: Configuring Networking 

 

21 

Dell EMC Ready Stack: Microsoft Hyper-V on PowerEdge 14G Servers and Unity Storage 

 Deployment Guide 

  

5. 

To verify that all the settings have been properly recorded, review the configuration 
from enable mode by running the following command: 

SW1# show running-config 

6. 

Repeat the preceding steps to configure the bottom Dell EMC Networking 
S5248F-ON switch in the configuration. 

 

The Networking S3048-ON switch connects to the network through the Networking 
S5248F-ON switches using a port channel that consists of one interface on each 
Networking S5248F-ON switch. Follow these steps: 

1. 

Configure the port-channel that will be used by running these commands: 

SW1(config)# interface port-channel 101 
SW1(conf-if-po-101)# description “OOB uplink” 
SW1(conf-if-po-101)# no shutdown 
SW1(conf-if-po-101)# switchport mode trunk 
SW1(conf-if-po-101)# switchport trunk allowed vlan 
100,110,120,210 
SW1(conf-if-po-101)# mtu 9216 
SW1(conf-if-po-101)# vlt-port-channel 101 
SW1(conf-if-po-101)# exit 

2. 

Configure the port that will be used for the port channel by running these 
commands: 

SW1(config)# port-group 1/1/12 
SW1(conf-pg-1/1/12)# mode Eth 10g-4x 
SW1(conf-pg-1/1/12)# exit 
SW1(config)# interface ethernet 1/1/48:1 
SW1(conf-if-eth1/1/48:1)# no shutdown 
SW1(conf-if-eth1/1/48:1)# description “OOB uplink”  
SW1(conf-if-eth1/1/48:1)# channel-group 101 mode active 
SW1(conf-if-eth1/1/48:1)# mtu 9216 
SW1(conf-if-eth1/1/48:1)# exit 

3. 

Repeat the preceding steps to configure the bottom Dell EMC Networking S5248F-
ON switch.

 

Configure the 
port channel 

Summary of Contents for PowerEdge 14G Series


























































Reviews:

No comments

Brands by name

Popular brands

Load more brands