manualshive.com logo in svg

Datalogic AMT58-PB Series, Instruction Manual

Share
Download
Datalogic AMT58-PB Series Instruction Manual Download Page 8

AMT58x-PB Profibus® 

 

 

2 

 

Mechanical safety 

 

  Install the device following strictly the information in the section “3 

- Mounting instructions”; 

 mechanical installation has to be carried out with stationary 

mechanical parts; 

  do not disassemble the encoder; 

  do not tool the encoder or its shaft; 

  delicate electronic equipment: handle with care; do not subject the 

device and the shaft to knocks or shocks; 

 

respect the environmental characteristics declared by 
manufacturer; 

  unit with solid shaft: in order to guarantee the maximum 

reliability over time of the mechanical parts, we recommend a 
flexible coupling to be installed to connect the encoder and the 
installation shaft; make sure the misalignment tolerances of the 
flexible coupling are respected; 

 

unit with hollow shaft: the encoder can be mounted directly on a 

shaft whose diameter has to respect the technical characteristics 
specified in the purchase order and clamped by means of the 
collar and the fixing plate into which an anti-rotation pin has to be 
inserted. 

 
 

Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]

Summary of Contents for AMT58-PB Series




























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands