manualshive.com logo in svg

Datalogic AMT58-PB Series, Instruction Manual

Share
Download
Datalogic AMT58-PB Series Instruction Manual Download Page 76

 

AMT58x-PB Profibus®

 

 

 

21 

6.3 Modes of operation

 

 

Profibus-DP devices allow operation using different communication 
modes (see Figure below): 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
NOTE 
All parameters -except for 

Preset value

- are transmitted in 

Set_Prm

 

mode. 

Preset value 

is transmitted only in 

Data_Exchange

 mode.

 

 
Types of communication

 

 

Transmission of data between Master and Slave is carried out using 
the following types of messages: 

 

 DDLM_Set_Prm: 

Used for configuring the slave. This communication mode is 
active immediately after power is turned ON and used to send 
parameters from Master to Slave (see section “6.4 
DDLM_Set_Prm“). 

 

 DDLM_Chk_Cfg: 

Sets the number of bytes used for data transmission in 

Data_Exchange

 mode (see section “6.5 DDLM_Chk_Cfg“). 

 

 

DDLM_Data_Exchange: 

Used as "standard operation mode". 
Used by Master to send the 

Preset value

; used by Slave to 

transmit position and velocity values (see section “6.6 
DDLM_Data_Exchange“).

 

 DDLM_Slave_Diag: 

Used when power is turned on and whenever Master needs to 
know diagnostic information from Slave device (see section “6.7 
DDLM_Slave_Diag“).

 

 Set_Slave_Address: 

Used to set a new node number via BUS (service SAP55, see 
section “6.8 Set_Slave_Address (service SAP55)“). 

Power-ON 

Wait_Prm 

Wait_Cfg 

Data_Exchang

Chk_Cfg_O

Set_Prm_O

Set_Prm_FAIL
Chk_Cfg_FAIL

Init_OK 

Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]

Summary of Contents for AMT58-PB Series




























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands