manualshive.com logo in svg

Datalogic AMT58-PB Series, Instruction Manual

Share
Download
Datalogic AMT58-PB Series Instruction Manual Download Page 65

AMT58x-PB Profibus® 

 

 

10 

4.5 Connection of the shield

 

 

Disentangle and shorten the shielding 1 and then bend it over the 
part 2; finally place the ring nut 3 of the connector. Be sure that the 
shielding 1 is in tight contact with the ring nut 3. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
4.6 Bus termination resistance 

 

A bus termination resistance is provided in the connection cap. This 
has to be activated as line termination in the last device. 
Use RT Switch to activate or deactivate the bus termination.

 

 

RT Description 

1 = 2 = ON 

Activated: if the encoder is the last device 
in the transmission line 

1 = 2 = OFF

Deactivated: if the encoder is not the last 
device in the transmission line 

 
 
 
 

 

 
 
 
4.7 Baud rate 

 

The baud rate is set by the Master via software during configuration 
of the node (slave). 
Supported baud rates are listed in the enclosed GSD file. 

Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]

Summary of Contents for AMT58-PB Series




























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands