manualshive.com logo in svg

Datalogic AMT58-PB Series, Instruction Manual

Share
Download
Datalogic AMT58-PB Series Instruction Manual Download Page 36

AMT58x-PB Profibus® 

 

 

30 

 
Types of communication messages 

 

Transmission of data between Master and Slave is carried out using 
the following types of messages: 
 

 

DDLM_Set_Prm: 

  Used for configuring the Slave. This communication mode is active 

immediately after power is turned ON and is used to send 
parameters from the Master to the Slave (see the section “6.4 
DDLM_Set_Prm” on page 31). 

 

 

DDLM_Chk_Cfg: 

  It sets the number of bytes used for data transmission in 

Data_Exchange

 mode (see section “6.5 DDLM_Chk_Cfg” on page 

37). 

 

 

DDLM_Data_Exchange: 

  This is the "standard operation mode". 
  It is used either by the Master to send the 

Preset

 value and by the 

Slave to transmit the 

Position 

value (see the section “6.6 

DDLM_Data_Exchange“ on page 38). 

 

 

DDLM_Slave_Diag: 

  It is used when the power is turned on and whenever the Master 

needs to know diagnostic information from the Slave device (see 
the section “6.7 DDLM_Slave_Diag” on page 40). 

 
 

Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]

Summary of Contents for AMT58-PB Series




























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands