manualshive.com logo in svg

DataKinetics DSC110, User Manual

Share
Download
DataKinetics DSC110 User Manual Download Page 27

DataKinetics DSC110 / DSC210 User Manual Issue 12 

 

Page 27 

Each PCM port in the system can be designated as a potential clock source and 
assigned a relative priority. The PCM port with the highest clock priority that 
currently contains a valid PCM signal is used as the synchronisation reference for 
the converter. All other outputs from the converter are synchronised to this 
reference source. In the event of the active synchronisation source failing, the 
converter will select the next highest priority input source as the synchronisation 
source. If no inputs contain a valid PCM signal then the converter will use a locally 
generated clock reference as the synchronisation source. 

Changes of PCM status are reported by the CS6 card to the central processor 
card allowing alarms to be entered in the system alarm log 

4.3.6 Alarm card 

The Alarm card performs a supervisory function within the converter. It contains 
the alarm relays and front panel LED driver circuitry to pass alarm indications to 
the user and monitoring circuitry for the power supply output rails, the fan fail 
detection circuitry and a temperature sensor. 

Connection to the alarm relay contacts is via a 15 way D-type socket mounted at 
the rear of the Alarm card. Two relays are provided designated “Prompt” and 
“Urgent”. In the event of a power failure the alarms both fall back into the alarming 
state. 

The fan fail detector, temperature and power supply output monitor circuits are 
used to detect system failures that are then reported to the central processor. 
Such failures are indicated to the user by entries in the Alarm Log and the 
respective front panel indicators being switched on. 

4.3.7 Network card 

The network card allows connection to the converter via Ethernet. This is used to 
provide a telnet MML interface for configuring the converter from a remote location 
and to transfer data to a Remote Data Centre. 

 

 

Summary of Contents for DSC110











































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands