Data Translation DT9816 Series User Manual Download Page 75

Page: 75 / 108

Supported Device Driver Capabilities

Thermocouple, RTD, and Thermistor Support

Table 16: Thermocouple, RTD, and Thermistor Support Options

DT9816 Series

A/D

D/A

DIN

DOUT

C/T

TACH

QUAD

Thermocouple Support

SupportsThernocouple

RTD Support

SupportsRTD

Thermistor Support

SupportsThermistor

Voltage Converted to Temperature

SupportsTemperatureDataInStream

Supported Thermocouple Types

ThermocoupleType

Supported RTD Types

RTDType

Supports CJC Source Internally in Hardware

SupportsCjcSourceInternal

Supports CJC Channel

SupportsCjcSourceChannel

Available CJC Channels

CjcChannel

Supports Interleaved CJC Values in Data Stream

SupportsInterleavedCjcTemperaturesInStream

Supported RTD Types

RTDType

RTD R0 Coefficient

RtdR0

Supports Temperature Filters

SupportsTemperatureFilters

Temperature Filter Types

TemperatureFilterType

Summary of Contents for DT9816 Series













































































































Search results

Summary of Contents for DT9816 Series

Reviews:

Brands by name

Popular brands

Data Translation DT9816 Series, User Manual

Search results

Summary of Contents for DT9816 Series

Reviews:

Brands by name

Popular brands