manualshive.com logo in svg

Data Translation DT9816 Series, User Manual

Share
Download
Data Translation DT9816 Series User Manual Download Page 71

Supported Device Driver Capabilities

71

Data Flow and Operation Options

 

Table 7: Data Flow and Operation Options

DT9816 Series

A/D

D/A

DIN

DOUT

C/T

TACH

QUAD

Single-Value Operation Support

SupportsSingleValue

Yes

Yes

Yes

Simultaneous Single-Value Output 
Operations

SupportsSetSingleValues

Continuous Operation Support

SupportsContinuous

Yes

Yes

Continuous Operation until Trigger

SupportsContinuousPreTrigger

Continuous Operation before & after Trigger

SupportsContinuousPrePostTrigger

Waveform Operations Using FIFO Only

SupportsWaveformModeOnly

Simultaneous Start List Support

SupportsSimultaneousStart

Supports Programmable Synchronization 
Modes

SupportsSynchronization

Synchronization Modes

SynchronizationMode

Interrupt Support

SupportsInterruptOnChange

FIFO Size, in Samples

FifoSize

8 kSamples

a

a.  The DT9816-S and DT9816-S-WTR have an input FIFO of 8 kSamples. The other models in the DT9816 Series 

have an effective input FIFO of 1.5 kSamples.

Muting and Unmuting the Output Voltage

SupportsMute

Auto-Calibrate Support

SupportsAutoCalibrate

Summary of Contents for DT9816 Series













































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands