manualshive.com logo in svg

Data Translation DT9816 Series, User Manual

Share
Download
Data Translation DT9816 Series User Manual Download Page 15

Overview

15

The key features are listed as follows:

• Six, independent, successive-approximation A/D converters with track-and-hold 

circuitry. Each converter uses a common clock and trigger for simultaneous sampling of 
all six analog input signals at up to 50 kHz per channel (DT9816 and DT9816-OEM), 
153.846 kHz per channel (DT9816-A), or 750 kHz per channel (DT9816-S and 
DT9816-S-WTR).

• Analog input subsystem provides 16-bit resolution and gains of 1 and 2 for effective 

full-scale input signal ranges of ±10 V and ±5 V.

• 8 digital inputs and 8 digital outputs

• 1, 16-bit counter/timer allows you to perform event counting, frequency measurement, 

and continuous pulse output (rate generation) operations

• Standard USB connector

• Shielded, rugged enclosure for noise immunity 

• Low  power  device

 – 

draws less than 100 mA

Summary of Contents for DT9816 Series













































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands