Data Translation DT9816 Series User Manual Download Page 25

Page: 25 / 108

Setting Up and Installing the Module

Unpacking

Open the shipping box and verify that the following items are present:

• DT9816, DT9816-A, DT9816-S, DT9816-S-WTR or DT9816-OEM module

• OMNI CD

• USB cable (not provided with the DT9816-OEM module)

If an item is missing or damaged, contact Data Translation. If you are in the United States, call
the Customer Service Department at (508)

946-5100

. An application engineer will guide you

through the appropriate steps for replacing missing or damaged items. If you are located
outside the United States, call your local distributor (see Data Translation’s web site
(www.

mccdaq

.com) for contact information).

Note:

DT9816 Series modules are factory-calibrated and require no further adjustment.

Summary of Contents for DT9816 Series













































































































Search results

Summary of Contents for DT9816 Series

Reviews:

Brands by name

Popular brands

Data Translation DT9816 Series, User Manual

Search results

Summary of Contents for DT9816 Series

Reviews:

Brands by name

Popular brands