Data I/O PSV7000 Page 68 Operator'S Manual Download

Page: 68 / 88

Operation ■ Running a Job on PSV7000

—64—

Data I/O • 096-0461-001G

back

Note:

Job throughput

as displayed in the Run window is affected

by the length of time a job is paused.

Nominal throughput

excludes paused time.

Emergency Stop

To prevent bodily injury or damage to equipment in an emergency,

press the red

Emergency Stop (E-Stop) button located on the front

and back of the machine. Pressing an E-Stop button immediately

stops motion of the PNP head and the gantry.

Figure 46: There are two Emergency Stop (E-Stop) buttons on the

machine.

To restart the System

—after pressing E-Stop

Figure 47: Popup message: Check the E-Stops.

Rotate the E-Stop button clockwise until it springs back to its full

height. Check the second E-Stop button if necessary.

Click

Retry

to continue. If possible the system will re-establish

communication within 30 seconds.

Front

Back

Summary of Contents for PSV7000

























































































Search results

Summary of Contents for PSV7000

Reviews:

Related manuals for PSV7000

Brands by name

Popular brands

Data I/O PSV7000, Operator'S Manual

Search results

Summary of Contents for PSV7000

Reviews:

Related manuals for PSV7000

Brands by name

Popular brands