background image

 
 
dspstak™ 21262sx User Manual 

 

Page 35 

 

Product Warranty 

 
Danville Signal Processing, Inc. products carry the following warranty: 

 
Danville Signal Processing products are warranted against defects in materials and workmanship. If 

Danville Signal Processing receives notice of such defects during the warranty period, Danville 
Signal Processing shall, at its option, either repair or replace hardware products, which prove to be 

defective. 
 

Danville Signal Processing software and firmware products, which are designated by Danville Signal 
Processing for use with our hardware products, are warranted not to fail to execute their 
programming instructions due to defects in materials and workmanship. If Danville Signal Processing 

receives notice of such defects during the warranty period, Danville Signal Processing shall, at its 
option, either repair or replace software media or firmware, which do not execute their 

programming instructions due to such defects. Danville Signal Processing does not warrant that 
operation of the software, firmware, or hardware shall be uninterrupted or error free. 

 
The warranty period for each product is one year from date of installation. 

 

Limitation of Warranty:  

 
The forgoing warranty shall not apply to defects resulting from: 

 

• 

Improper or inadequate maintenance by the Buyer; 

• 

Buyer-supplied software or interfacing; 

• 

Unauthorized modification or misuse; 

• 

Operation outside the environmental specification of the product; 

• 

Improper site preparation and maintenance. 

 

Exclusive Remedies: 

 
The remedies provided herein are the Buyer’s sole and exclusive remedies. In no event shall 
Danville Signal Processing, Inc. be liable for direct, indirect, special, incidental or consequential 

damages (including loss of profits) whether based on contract, tort, or any other legal theory. 

Summary of Contents for dspstak 21262sx




































Reviews: