background image

Troubleshooting

Increase the ambient temperature of the unit.

Supply a trickle amount of current to the drive whenever the motor is stopped by setting 

parameter 2-00 DC Hold/Preheat Current

 to

5% and 

parameter 1-80 Function at Stop

.

8.4.63 ALARM 67, Option Module Configuration has Changed

Cause

One or more options have either been added or removed since the last power-down.

Troubleshooting

Check that the configuration change is intentional and reset the unit.

8.4.64 ALARM 68, Safe Stop Activated

Cause

Safe Torque Off (STO) has been activated.

Troubleshooting

To resume normal operation, apply 24 V DC to terminal 37, then send a reset signal (via bus, digital, or by pressing [Reset]).

8.4.65 ALARM 69, Power Card Temperature

Cause

The temperature sensor on the power card is either too hot or too cold.

Troubleshooting

Check that the ambient operating temperature is within the limits.

Check for clogged filters.

Check fan operation.

Check the power card.

8.4.66 ALARM 70, Illegal FC Configuration

Cause

The control card and power card are incompatible.

Troubleshooting

To check compatibility, contact the Danfoss supplier with the type code from the unit nameplate and the part numbers on the

cards.

Maintenance, Diagnostics, and

Troubleshooting

Operating Guide  | VLT® AQUA Drive FC 202

AQ275652274277en-000101 / 130R0708

120 | Danfoss A/S © 2020.01

Summary of Contents for VLT AQUA Drive FC 202















































































































































































Reviews: