background image

 

-  -

HLP-C

+    

Inverters

I.Introduction 

Thank you for purchasing and using the general-purpose inverter 

of HLP- C

+

 Series of multi-functions and high performance.

The inverter of HLP- C

+

 Series has been developed on basis 

of HLP-A Series keeping the main functions of HLP-A Series 

and with additional functions on request of customers as well 

as smaller size. So the inverter of HLP- C

+

 Series features more 

compact and more powerful functions.

Please read carefully the operation manual before put the 

inverter to use so as to correctly install and operate the inverter, 

give full play to its functions and ensure the safety. Please keep 

the operation manual handy for future reference, maintenance, 

inspection and repair.

Due to the inverter of a kind of electrical and electronic product 

it must be installed, tested and adjusted with parameters by 

specialized engineering persons of motor. The marks of               

               and other simbols in the manual remind you of the 

safety and prevention caustions during the transportation, 

installation,  running  and  inspection.  Please  follow  these 

instructions to make sure the safe use of the inverter. In case of 

any doubt please contact our local agent for consultation. Our 

professional persons are willing and ready to serve you.

The manual is subject to change without notice.

Danger

Caution

 

Danger

  indicates wrong use may kill or injure people.

Caution

  indicates wrong use may damage the inverter 

                or mechanical system.

 Danger

● Be sure to turn off the input power supply before wiring.

● Do not touch any internal ecectrical circuit or component 

when the charging lamp is still on after the AC power supply 

is disconnected, which means the inverter still has high 

voltage inside and it is very dangerous.

Summary of Contents for Holip HLP-C+ Series





















Reviews: