background image

 

-  -

HLP-C

+    

Inverters

Caution

● Check to be sure that the voltage of the main circuit AC 

power supply matches the input voltage of the inverter.

Caution

 

● 

E  

 symbol is the ground terminal. Be sure to make correct 

ground connection of the earth terminals of the motor and 

the inverter for safety. E can't be connected to Line zero.

● No contactor should be installed between the power supply 

and theinverter to use it for starting or stopping of the 

inverter. Otherwise it will affect the service life of the 

inverter.

Danger

● R.S.T terminals are power input terminals, never mixed with 

U.V.W terminals. Be sure that the wiring of the main circuit 

is correct. Otherwise it will cause damages of the inverter 

when the power is delivered to it.

● Do not carry the front cover of the inverter directly when 

handling, It should be handled with the base to prevent 

the fall off of the front cover and avoid the dropping of the 

inverter,which may possibly cause the injuries to people and 

the damages to the inverter.

● Mount the inverter on a metal or other noncombustible 

material to avoid the risk of fire.

● Install the inverter in a safe site, avoid high temperature, 

direct sunlight, humid air or water.

● Keep the inverter from the reach of children or persons not 

concerned.

II.Safety Precautions

⑴ Before the Power Up 

Caution

 

Summary of Contents for Holip HLP-C+ Series





















Reviews: