manualshive.com logo in svg

Dallas Semiconductor MAXIM DS3112, Manual, Page: 63 / 133

Share
Download
Dallas Semiconductor MAXIM DS3112 Manual Download Page 63

DS3112 

 

 

63 of 133 

 

Register Name: 

T2E2CR2 

Register Description: 

T2/E2 Control Register 2 

Register Address: 

32h 

 
Bit 

#  7 6 5 4 3 2 1 0 

Name 

— 

LOFG7 LOFG6 LOFG5 LOFG4 LOFG3 LOFG2 LOFG1 

Default 

— 0 0 0 0 0 0 0 

 
Bit 

#  15 14 13 12 11 10  9  8 

Name  — — — — 

E2Sn4 

E2Sn3 

E2Sn2 

E2Sn1 

Default — — — — — — — — 

Note: Bits that are underlined are read-only; all other bits are read-write. 

Bits 0 to 6: T2/E2/G.747 Transmit Loss Of Frame Generation (LOFGn where n = 1 to 7).

 A zero to one 

transition on this bit will cause the T2/E2/G.747 transmit formatter to generate enough framing bit errors to cause 
the far end to lose frame synchronization. This bit must be cleared and set again for a subsequent set of errors to be 
generated

. 

MODE FRAMING 

ERRORS 

GENERATED 

T3 Mode 

Four consecutive F bit errors 

E3 Mode 

Four consecutive FAS words of 0000101111 generated instead of the normal FAS word, 
which is 1111010000 (i.e., all FAS bits are inverted) 

G.747 Mode 

Four consecutive FAS words of 000101111 generated instead of the normal FAS word, 
which is 111010000 (i.e., all FAS bits are inverted) 

 

Bits 8 to 11: E2 Transmit National Bit Setting (E2Snn where n = 1 to 4).

 These bits are ignored in the T3 and 

G.747 modes. The received Sn can be read from the T2E2 Status Register 2. 
 

0 = force the Sn bit to zero 

 

1 = force the Sn bit to one

 

Summary of Contents for MAXIM DS3112






































































































































Reviews:

No comments