Dallas Semiconductor MAXIM DS3112 Manual Download

Page: 43 / 133

DS3112

43 of 133

Figure 4-6. T2E2SR1 Status Bit Flow

Alarm Latch

Change in State Detect

LOF1
(T2E2SR1
Bit 0)

Internal LOF
Signal from
T2/E2 Framer 1

Alarm Latch

Change in State Detect

Internal LOF
Signal from
T2/E2 Framer 2

Alarm Latch

Change in State Detect

Internal LOF
Signal from
T2 Framer 7

Mask

IELOF
(T2E2SR1
Bit 7)

LOF2
(T2E2SR1
Bit 1)

LOF7
(T2E2SR1
Bit 6)

Alarm Latch

Change in State Detect

AIS1
(T2E2SR1
Bit 8)

Internal AIS
Signal from
T2/E2 Framer 1

Alarm Latch

Change in State Detect

Internal AIS
Signal from
T2/E2 Framer 2

Alarm Latch

Change in State Detect

Internal AIS
Signal from
T2 Framer 7

Mask

IEAIS
(T2E2SR1
Bit 15)

AIS2
(T2E2SR1
Bit 9)

AIS7
(T2E2SR1
Bit 14)

Mask

T2E2SR1
(IMSR Bit 5)

INT*
Hardware
Signal

T2E2SR1
Status Bit
(MSR Bit 5)

Event
Latch

NOTE: ALL EVENT AND ALARM LATCHES ABOVE ARE CLEARED WHEN THE T2E2SR1 REGISTER IS READ.

Summary of Contents for MAXIM DS3112






































































































































Search results

Summary of Contents for MAXIM DS3112

Reviews:

Related manuals for MAXIM DS3112

Brands by name

Popular brands

Dallas Semiconductor MAXIM DS3112, Manual

Search results

Summary of Contents for MAXIM DS3112

Reviews:

Related manuals for MAXIM DS3112

Brands by name

Popular brands