Dallas Semiconductor MAXIM DS3112 Manual Download | Manualshive

Page: 28 / 133

background image

DS3112

28 of 133

2.7 High-Speed (T3 or E3) Receive Port Signal Description

Signal Name:

HRPOS/HRNEG

Signal Description:

High-Speed (T3 or E3) Receive Serial Data Inputs

Signal Type:

Input

These input signals sample the serial data from the incoming T3 data streams or E3 data streams. Data
can be clocked into the device either on rising edges (normal clock mode) or falling edges (inverted clock
mode) of the associated HRCLK. This option is controlled via the HRCLKI control bit in Master Control
Register 2 (Section

Signal Name:

HRCLK

Signal Description:

High-Speed (T3 or E3) Receive Serial Clock Input

Signal Type:

Input

This signal is used to clock data in from the incoming T3 or E3 data streams. The T3 or E3 serial data
streams at the HRPOS and HRNEG signals can be clocked into the device either on rising edges (normal
clock mode) or falling edges (inverted clock mode) of HRCLK. This option is controlled via the HRCLKI
control bit in Master Control Register 2 (Section

Note:

The HRCLK must be present for the host to be able to obtain status information (except the LOTC

and LORC status bits, see Section

) from the device.

2.8 High-Speed (T3 or E3) Transmit Port Signal Description

Signal Name:

HTPOS/HTNEG

Signal Description:

High-Speed (T3 or E3) Transmit Serial Data Outputs

Signal Type:

Output

These output signals present the outgoing T3 data streams or E3 data streams. Data can be clocked out of
the device either on rising edges (normal clock mode) or falling edges (inverted clock mode) of HTCLK.
This option is controlled via the HTCLKI control bit in Master Control Register 2 (Section

these outputs can be forced high or low via the HTDATH and HTDATL control bits respectively in
Master Control Register 2 (Section

Signal Name:

HTCLK

Signal Description:

High-Speed (T3 or E3) Transmit Serial Clock Output

Signal Type:

Output

This output signal is used to clock T3 or E3 data out of the device. The T3 or E3 serial data streams at the
HTPOS and HTNEG signals can be clocked out of the device either on rising edges (normal clock mode)
or falling edges (inverted clock mode) of HTCLK. This option is controlled via the HTCLKI control bit
in Master Control Register 2 (Section

«
...
26
27
28
29
30
...
»

Summary of Contents for MAXIM DS3112






































































































































Reviews:

No comments

Related manuals for MAXIM DS3112

Brand: Huayi Pages: 46

Brand: Greenlee Pages: 52

Brand: Greenlee Pages: 72

Brand: Telco Pages: 24

Brand: Mastech Pages: 14

Brand: Mastech Pages: 18

Brand: BGS technic Pages: 36

Brand: Amprobe Pages: 98

Brand: Amprobe Pages: 96

Brand: Amprobe Pages: 112

SNR-MPX-2E1-SFP

Brand: NAG Pages: 16

Brand: Mastech Pages: 14

Brand: Mastech Pages: 14

Brand: Amprobe Pages: 89

Brand: Mastech Pages: 11

Brand: Pantron Pages: 12

Brand: CableWorld Pages: 2

Brand: Netzerotools Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands