Dallas Semiconductor MAXIM DS3112 Manual Download

Page: 45 / 133

DS3112

45 of 133

Figure 4-9. T3E3SR Status Bit Flow

Mask

T3E3SR
(IMSR Bit 9)

INT*
Hardware
Signal

T3E3SR
Status Bit
(MSR Bit 9)

Alarm Latch

Receive LOS
Signal from
T3/E3 Framer

LOS
(T3E3SR Bit 0)

Mask

LOS (IT3E3SR Bit 0)

Change in State Detect

Alarm Latch

Receive LOF
Signal from
T3/E3 Framer

LOF
(T3E3SR Bit 1)

Mask

LOF (IT3E3SR Bit 1)

Change in State Detect

Alarm Latch

Receive AIS
Signal from
T3/E3 Framer

AIS
(T3E3SR Bit 2)

Mask

AIS (IT3E3SR Bit 2)

Change in State Detect

Alarm Latch

Receive RAI
Signal from
T3/E3 Framer

AIS
(T3E3SR Bit 3)

Mask

AIS (IT3E3SR Bit 3)

Change in State Detect

Alarm Latch

Receive Idle
Signal from
T3/E3 Framer

T3IDLE
(T3E3SR Bit 4)

Mask

T3IDLE (IT3E3SR Bit 4)

Change in State Detect

Event Latch

Receive Start
Of Frame
Signal from
T3/E3 Framer

RSOF
(T3E3SR Bit 5)

Mask

RSOF (IT3E3SR Bit 5)

Event Latch

Transmit Start
Of Frame
Signal from
T3/E3 Framer

TSOF
(T3E3SR Bit 6)

Mask

TSOF (IT3E3SR Bit 6)

Event Latch

NOTE: ALL EVENT AND ALARM LATCHES ABOVE ARE CLEARED WHEN THE T3E3SR REGISTER IS READ.

Summary of Contents for MAXIM DS3112






































































































































Search results

Summary of Contents for MAXIM DS3112

Reviews:

Related manuals for MAXIM DS3112

Brands by name

Popular brands

Dallas Semiconductor MAXIM DS3112, Manual

Search results

Summary of Contents for MAXIM DS3112

Reviews:

Related manuals for MAXIM DS3112

Brands by name

Popular brands