manualshive.com logo in svg

Dallas Semiconductor MAXIM DS3112, Manual, Page: 46 / 133

Share
Download
Dallas Semiconductor MAXIM DS3112 Manual Download Page 46

DS3112 

 

 

46 of 133 

 

Register Name: 

IMSR 

Register Description: 

Interrupt Mask for Master Status Register 

Register Address: 

0Ah 

 
Bit 

#  7 6 5  4 3 2 1 0 

Name — 

T2E2SR2 

T2E2SR1 

FEAC 

HDLC 

BERT 

COVF 

OST 

Default 

— 0 0 0 0 0 0 0 

 
Bit 

#  15 14 13 12 11 10  9  8 

Name  — — — — 

LORC 

LOTC 

T3E3SR 

T1LB 

Default 

— — — —  0  0  0  0 

Bit 0: One-Second Timer Boundary Occurrence (OST).

  

 

0 = interrupt masked 

 

1 = interrupt unmasked 

Bit 1: Counter Overflow Event (COVF).

  

 

0 = interrupt masked 

 

1 = interrupt unmasked 

Bit 2: Change in BERT Status (BERT).

  

 

0 = interrupt masked 

 

1 = interrupt unmasked 

Bit 3: Change in HDLC Status (HDLC).

  

 

0 = interrupt masked 

 

1 = interrupt unmasked 

Bit 4: Change in FEAC Status (FEAC).

  

 

0 = interrupt masked 

 

1 = interrupt unmasked 

Bit 5: Change in T2/E2 LOF or AIS Status (T2E2SR1).

 

 

0 = interrupt masked 

 

1 = interrupt unmasked 

Bit 6: Change in T2/E2 RAI Status (T2E2SR2).

  

 

0 = interrupt masked 

 

1 = interrupt unmasked 

Bit 8: T1 Loopback Detected (T1LB).

  

 

0 = interrupt masked 

 

1 = interrupt unmasked 

Bit 9: Change in T3/E3 Framer Status (T3E3SR).

  

 

0 = interrupt masked 

 

1 = interrupt unmasked 

Bit 10: Loss Of Transmit Clock (LOTC).

  

 

0 = interrupt masked 

 

1 = interrupt unmasked 

Bit 11: Loss Of Receive Clock (LORC).

  

 

0 = interrupt masked 

 

1 = interrupt unmasked 

Summary of Contents for MAXIM DS3112






































































































































Reviews:

No comments