Daktronics P1146 Display Manual Download Page 3

Page: 3 / 29

– i –

Table of Contents

1 Introduction .........................................1

How to Use This Manual ............................1
Product Description ...................................2
Definitions ...................................................2

2 Mechanical and Electrical

Installation ...........................................4

Mechanical Installation ............................4
Computer to SI-32 Connections ..............4

RS232 System ..........................................4
RS422 System ..........................................5
Switches to SI-32 .....................................6

SPST .......................................................6
SPDT ......................................................7
Momentary ..........................................7
BCD (Binary Coded Decimal) ...........8
Rotary ...................................................9

3 Version 3 Software Operation..........10

Using the Venus

1500 Version 3 Software .

...................................................................10
Using the Switch Interface ......................10

SI-32 Mode Setup ..............................12
Toggle Mode .....................................12
SPST Switch .........................................12
SPDT Switch ........................................12

Momentary Mode ...................................13
BCD Mode (Binary Coded Decimal) ....13
Connecting Two SI-32 Units ....................14
SI-32 Setup ................................................14

4 Version 4 Software Operation..........15

Using the Venus

1500 Version 4 Software

...................................................................15
Using the Switch Interface ......................15

SI-32 Mode Setup .................................16
Toggle Mode .........................................16
SPST Switch ............................................16
SPDT Switch ............................................16

Momentary Mode ...................................17
BCD Mode (Binary Coded Decimal) ....17
Connecting Two SI-32 Units ....................18
SI-32 Setup ................................................18

5 Maintenance and Troubleshooting ....

............................................................19

Getting Started ........................................19
Technical Specifications .........................19
LED Functions ...........................................19
Routine/Preventative Maintenance .....20
Troubleshooting .......................................21
Replacements Parts List ..........................22
Daktronics Exchange and Repair &

Return Programs ......................................22

Exchange Program ..............................22
Repair & Return Program .....................23
Shipping Address ..................................23
Email ......................................................23

A Reference Drawings .........................25

Summary of Contents for P1146






























Search results

Summary of Contents for P1146

Reviews:

Related manuals for P1146

Brands by name

Popular brands

Daktronics P1146, Display Manual

Search results

Summary of Contents for P1146

Reviews:

Related manuals for P1146

Brands by name

Popular brands