Daktronics P1146 Display Manual Download Page 26

Page: 26 / 29

Maintenance and Troubleshooting

Replacements Parts List

Daktronics Exchange and Repair & Return Programs

To serve customers’ repair and maintenance needs, Daktronics offers both an Exchange

Program and a Repair & Return Program.

Exchange Program

Daktronics offers a unique Exchange Program as a quick service for replacing key parts

in need of repair. If a part requires repair or replacement, Daktronics sends the customer

a replacement, and the customer sends the defective part to Daktronics. This decreases

display downtime.
To participate in the Exchange Program, follow these steps.

1. Call Daktronics Customer Service:

Market Description

Customer Service Number

Department of Transportation, mass transits,

airports, parking facilities

800-833-3157

2. When the new exchange part is received, mail the old part to Daktronics.

If the replacement part fixes the problem, send in the problem part which is being

replaced.

Package the old part in the same shipping materials in which the replacement

part arrived.

Fill out and attach the enclosed UPS shipping document.

Ship the part to Daktronics.

Part Description

Part Number

Switch Interface

0A-1146-0018

Signal Converter-wire

0A-1127-0237

Serial Cable; RS232 DB9F to DB25M, 6"

W-1249

DB9 to DB25 Adaptor

A-1603

DB9 Female to RJ11 Female Adaptor

0A-1115-0042

DB25 Female to RJ11 Female Adaptor

0A-1115-0044

Venus 1500

V3 Operator’s Manual

ED-13530

Venus 1500

V4 Operator’s Manual

DD1370296

Summary of Contents for P1146






























Search results

Summary of Contents for P1146

Reviews:

Related manuals for P1146

Brands by name

Popular brands

Daktronics P1146, Display Manual

Search results

Summary of Contents for P1146

Reviews:

Related manuals for P1146

Brands by name

Popular brands