Daktronics P1146 Display Manual Download Page 23

Page: 23 / 29

Maintenance and Troubleshooting

5 Maintenance and Troubleshooting

Reference Drawings:

System Riser Diagram; Single Pole (SP).............................................................

DWG-093476

System Riser Diagram; Momentary ...................................................................

DWG-096221

System Riser Diagram; BCD Switch ...................................................................

DWG-096315

System Riser Diagram; Rotary ............................................................................

DWG-097099

OSI-32 Wiring Diagram, Toggle Switches .........................................................

DWG-097134

Assembly, Switch Interface, 32 Input ................................................................

DWG-086312

Getting Started

Disconnect power before any repair or maintenance work is done on the interface.

Qualified service personnel must make any access to internal electronics.

Disconnect power when the SI-32 interface is not in use.

Technical Specifications

Functional Description:

The switch interface is used in conjunction with one or more

Venus

1500 controlled displays. The unit has a RS232 input, RS422 input, and RS422

output. The inputs are used for connection to a Venus

1500 Software System for

message programming. The output is connected to one or more electronics message

displays. Thirty-two isolated inputs control what messages will be displayed.

LED Functions

Power:

The green power LED should be on continuously, indicating that power is on.

Run/TX:

The red RUN/TX LED should blink slowly indicating the microprocessor is running.

The LED should blink faster while transmitting.

RX:

The amber RX LED should flash when the Venus

1500 Software is communicating with

the displays. If the Venus

1500 Software is disconnected, the amber TX LED may remain

on.

Note:

This unit needs only the Venus

1500 Software for initial message programming.

Summary of Contents for P1146






























Search results

Summary of Contents for P1146

Reviews:

Related manuals for P1146

Brands by name

Popular brands

Daktronics P1146, Display Manual

Search results

Summary of Contents for P1146

Reviews:

Related manuals for P1146

Brands by name

Popular brands