[7]
MAN #650793
S
etting warning levels on a VFD3 or VFD3X system:
1. Press and hold SW1 while turning the key on.
a. The message display will show
SETUP
while speed display will show
.
2. Release SW1 (I) to display
SPEED
and
3. Tap SW1 (I) several times to display
BIM
and
4. Press and hold SW1 (I) when
BIM
and
are displayed.
5. Keep holding to display
SCAN X
and
-
.
a.
X
= the number of BIM channels found,
4
will be displayed for only a BIM-22-3.
6. Release the SW1 (I) to display
SCAN
and
7. Tap SW1 (I) once, to display
SETUP
and
.
8. Press and hold SW1 (I) to display
SETUP
and
-
.
9. Releasing SW1 (I) will display
LF TIRE
and
a.
The BIM-22-3 module will flash
.
It is
not
a problem during setup.
b. Each tire will have a different channel RF=C4, LF=C5, and RR=C6.
c. If a BIM-04-2 is connected, the displays will show TEMP and C1.
d. If a BIM-04-2 is connected, tap SW1 (I) once to change it to LF TIRE and C3.
10. Press and hold SW1 (I) until
LABEL
and
–
are displayed.
11. Release to display
LF TIRE
and
.
12. Press and hold SW1 (I) to display
WARN
and
-
. A second message center will display
LF TIRE
.
13. Release to display
L 25
* and
. A second message will display
LF TIRE
.
a.
L
represents low pressure and the number is the PSI. 25 is the factory default.
b. A single message center will alternate between
L 25
and
LF TIRE
.
14. Tap SW1 (I) to increment the low-pressure warning point.
a. If 25 PSI is fine, then hold SW1 (I) until
L 25
and
are displayed.
b. The low-pressure range is 05 to 99 PSI.
c. If you tap past your desired PSI, you must tap up 99 before it restarts at 05 PSI.
15. Press and hold to save the low-pressure warning and
L XX
(XX=PSI value) and
–
are displayed.
16. Release SW1 (I) to display
H 35
* and
are displayed. A second message center will display
LF TIRE
.
a.
H
represents high pressure and the number is the PSI. 35 is the factory default.
b. A single message center will alternate between
H 35
and
LF TIRE
.
17. Tap SW1 (I) to increment the high-pressure warning point.
a. If 35 PSI is fine, then hold SW1 (I) until
H 35
and
–
are displayed.
b. The low-pressure range is 05 to 99 PSI.
c. If you tap past your desired PSI, you must tap up 99 before it restarts at 05 PSI.
18. Press and hold to save the high-pressure warning and
H XX
(XX=PSI value) and
– are displayed.
19. Release to display
SKIP
and
a. To do the Locate process see the next page.
20. Press and hold SW1 (I) to skip past the Location process,
SKIP
and
–
will display.
21. Release SW1 (I) to display
DONE
and
.
a. To change warnings more warnings, tap SW1 (I) to display another tire and repeat steps 6 to 21.
22. To exit: when
DONE
and
are displayed, press and hold SW1 (I) until
DONE
and
are displayed.
Summary of Contents for BIM-22-3
Page 15: ...15 MAN 650793 NOTES...
