[5]
MAN #650793
Setting warning levels on a VHX system:
1. Hold the SW1 (I) switch from the instrument system control box while turning the key on.
a. The message display should show
SETUP
.
2. Release SW1 (I) - LCD1 should show
SETUP SPEED
.
3. Tap SW1 (I) until
SETUP BIM
is shown on the message display.
4. Press and hold SW1 (I).
a. The message display will show
SCANNING
… Release SW1 (I).
b. The display will scroll through the 16 possible channels used.
5. If
FOUND 00
and
00 ERRORS
is shown:
a. Check and reseat all BIM connections.
b. Tap SW1 (I) to show
BIM DONE
. Tap SW1 (I) again to show
BIM SCAN
.
c. Press and hold SW1 (I) to scan for modules again.
6. If
FOUND 00
and
XX ERRORS
is shown (X= a number):
a. If multiple BIM units may be installed, the display may also show:
FOUND 01
and
00 ERRORS
.
b.
Follow the “Change ID” for other BIM modules to correct conflicts, the enter setup again start over.
7. If
FOUND xx
and
00 ERRORS
shown (X=should be the number of BIM channels used):
a. One BIM-22-3 will read:
FOUND 04
and
00 ERRORS
.
b. If a BIM-22-3 is used with a BIM-19-2 the scan should read:
FOUND 08
and
00 ERRORS
.
c. Tap SW1 (I) until
BIM SCAN
is shown.
8. Tap SW1 (I) once so the display shows
BIM SETUP
.
a. The BIM setup options are
SCAN
,
SETUP
, and
DONE
.
9. Tap SW1 (I) once to display
SETUP
.
10. Press and hold SW1 (I) until the display will show
BIM CH 03 LF TIRE
.
a. If another BIM is present, you may see more BIM channels.
b. A BIM-04-2 will occupy
BIM CH 1 TEMP
.
c. Tap SW1 (I) to display
BIM CH 3 LF TIRE
.
11. Press and hold SW1 (I) to change display to
CH 03 LABEL LF TIRE
.
a.
The BIM-22-3 module will flash
.
It is
not
a problem during setup
12. Press and hold SW1 (I) until
CH 03 LOW WARN SET
is displayed.
13. Releasing SW1 (I) will display the LF corner low air pressure warning point of 25 (factory default).
14. Tap SW1 (I) to increment the low-pressure warning point.
a. If 25 PSI is sufficient as a low-pressure point, press and hold SW1 (I) to save.
b. Low pressure range is from 05 to 99 PSI.
c. If you tap past your desired PSI, you must tap up 99 before it restarts at 05 PSI.
15. Press and hold SW1 (I) to save low pressure warning
–
CH 03 HI WARN SET
will be display.
16. Releasing SW1 (I) will display the LF corner high air pressure warning of 35 (factory default).
17. Tap SW1 (I) to increment the high-pressure warning point.
a. If 35 PSI is sufficient as a high-pressure, point press and hold SW1 (I) to save.
b. Low pressure range is from 05 to 99 PSI.
c. If you tap past your desired PSI, you must tap up 99 before it restarts at 05 PSI.
18. Press and hold SW1 (I) to save high-pressure warning point.
19. When SW1 (I) is released,
TIRE LOCATE SKIP
will be displayed.
a. To do the
TIRE LOACTE
proceed to the next page.
b. To skip over Tire Locate press and hold SW1 (I) until
BIM CH 04 rF TIRE
.
c. Repeat step 11 to step 19 for remaining tires.
20. If done setting warning points and locations, tap SW1 (I) until
BIM SETUP DONE
is displayed.
21. Press and hold SW1 (I) until a big
DONE
is displayed. Release SW1 (I) and turn the key off.
Summary of Contents for BIM-22-3
Page 15: ...15 MAN 650793 NOTES...
