background image

17

English

Procedure for checking maximum concentration

Check the maximum concentration level in accordance with steps 1 
to 4 below and take whatever action is necessary to comply.

1.

Calculate the amount of refrigerant (kg) charged to each system 
separately.

Note

Where a single refrigerant facility is divided into 2 entirely inde-
pendent refrigerant systems then use the amount of refrigerant 
with which each separate system is charged.

2.

Calculate the smallest room volume (m

)

Incase like the following, calculate the volume of (A), (B) as a sin-
gle room or as the smallest room.

A.

Where there are no smaller room divisions

B.

Where there is a room division but there is an opening 

between the rooms sufficiently large to permit a free flow of 
air back and forth.

1.

opening between rooms

2.

partition 

(Where there is an opening without a door or where there are open-
ings above and below the door which are each equivalent in size to 
0.15% or more of the floor area.)

3.

Calculating the refrigerant density using the results of the calcu-
lations in steps 1 and 2 above.

If the result of the above calculation exceeds the maximum con-
centration level then make similar calculations for the second then 
third smallest room and so until the result falls short of the maxi-
mum concentration.

4.

Dealing with the situations where the result exceeds the maxi-
mum concentration level.
Where the installation of a facility results in a concentration in 
excess of the maximum concentration level then it will be neces-
sary to revise the system. Please consult your Daikin supplier.

NOTES

amount of refriger-
ant in a single unit 
system (amount of 
refrigerant with 
which the system 
is charged before 
leaving the factory)

+

additional charging 
amount (amount of 
refrigerant added 
locally in accordance 
with the length or 
diameter of the refrig-
erant piping)

=

total amount 
of refriger-
ant (kg) in 
the system

total volume of refrigerant in the 
refrigerant system

maximum concen-
tration level (kg/m

3

)

size (m

) of smallest room in which 

there is an indoor unit installed

1

2

01_EN_3P201178-4B.fm  Page 17  Friday, May 18, 2007  7:58 PM

Summary of Contents for VRV III REYQ8PY1B

























Reviews: