Daikin RZQ71D7V1B, Installation Manual

Page: 16 / 20

Installation manual
13
RZQ71~14 RZQ7 RZQ100~140B8W1B
Split System air conditioners
4PW48323-1B
Precautions on wiring of power supply and inter-unit
wiring
■
Use a round crimp-style terminal for connection to the power
supply terminal board. In case it cannot be used due to
unavoidable reasons, be sure to observe the following
instruction.
- Do not connect wires of different gauge to the same power
supply terminal. (Looseness in the connection may cause
overheating.)
- When connecting wires of the same gauge, connect them
according to the below figure.
■
Use the correct screwdriver to tighten the terminal screws.
Small screwdrivers can damage the screw head and prevent
appropriate tightening.
■
Over-tightening the terminal screws can damage the screws.
■
See the table below for tightening torques for the terminal
screws.
■
Refer to the installation manual attached to the indoor unit for
wiring of indoor units, etc.
■
Attach an earth leakage breaker and fuse to the power supply
line.
(See figure 9)
■
In wiring, make certain that prescribed wires are used, carry out
complete connections, and fix the wires so that outside forces
are not applied to the terminals.
Specifications of standard wiring components
Only for RZQ71~140D: Equipment complying with EN/IEC 61000-3-12
(1)
.
T
EST OPERATION
Pre-run checks
Tightening torque (N•m)
M4 (X1M) 1.2~1.8
M4 (EARTH) 1.2~1.4
M5 (X1M) 2.0~3.0
M5 (EARTH) 2.4~2.9
I Pair
II Twin
III Triple
IV Double twin
M Master
S Slave
1 Earth leakage breaker
2 Fuse
3 Remote controller
1 2 3
1 Round pressure terminal
2 Cut out section
3 Cup washer
RZQ 71V1 100V1 125V1 140V1 100W1 125W1 140W1
Minimum circuit
amps (MCA)
(a)
(a) Stated values are maximum values (see electrical data of combination with indoor
units for exact values).
18.9 27.6 28.8 17.1 18.3
Recommended
field fuse (A)
20 32 20
Wire type
(b)
(b) Only in protected pipes, use H07RN-F when protected pipes are not used.
H05VV-U3G H05VV-U5G
Size
Wiring size must comply with the applicable local and
national code
Wire type of
wiring between
the units
H05VV-U4G2.5
NOTE The earth leakage breaker must be a high-speed type
breaker of 30 mA (<0.1 s).
(1) European/International Technical Standard setting the limits for harmonic
currents produced by equipment connected to public low-voltage systems
with input current >16 A and
≤
75 A per phase.
WARNING
Live parts can be easily touched by accident.
Never leave the unit unattended during installation or
servicing when the service panel is removed.
NOTE
Note that during the first running period of the unit,
required power input may be higher. This phenomenon
originates from the compressor that requires a 50-hour
run-in period before reaching smooth operation and
stable power consumption.
Items to check
Electrical wiring
Inter-unit wiring
Ground wire
■
Is the wiring as mentioned on the wiring
diagram?
Make sure no wiring has been forgotten and that
there are no missing phases or reverse phases.
■
Is the unit properly grounded?
■
Is the wiring between units connected in series
correct?
■
Are any of the wiring attachment screws loose?
■
Is the insulation resistance at least 1 M
Ω
?
- Use a 500 V mega-tester when measuring
insulation.
- Do not use a mega-tester for low-voltage
circuits.
Refrigerant piping
■
Is the size of the piping appropriate?
■
Is the insulation material for the piping attached
securely?
Are both the liquid and gas pipes insulated?
■
Are the stop valves for both the liquid side and
the gas side open?
Extra refrigerant
■
Did you write down the extra refrigerant and the
refrigerant piping length?