background image

English

24

Troubleshooting

Before consulting your dealer or asking for repairs, check the following points. 
If the problems still can not be solved, consult your dealer.

The unit does not operate.

The unit does not operate 
even if the ON / OFF button is 
pressed.

Is the front panel correctly set? 

 

Page 10.

 

Are the projections on the rear of the front panel broken?

 

Check the projections. 

 

Î

Page 16.

 

 

Consult your dealer if the projections are broken.

Is the battery of the remote controller run down? 

 

Page 12.

 

The desired results are not obtained.

The air is not cleaned.

Is the unit located where the air does not reach the entire room 

 

or is something obstructing the air

fl

 ow? 

Select an unobstructed location from where the air can reach the 

 

Î

entire room.

Is the pre

fi

 lter, the pleated 

fi

 lter or UNIT1 dirty?

 

Perform cleaning. 

 

Î

Page 15-21.

 

If odour of the deodorising catalyst unit is a concern, lightly wet 
the surface of the unit using an atomiser, and then dry it in a 
shaded and well-ventilated place.

Although there is odour, the 
green lamp remains lit.

Is a large amount of odour generated when starting operation of 

 

the unit?

The odour level of the initial 1 minute is used as the standard for 

 

Î

the sensitivity of the odour sensor. Operate the unit with an 
increased air

fl

 ow. 

Page 8.

 

Modify the standard sensitivity of the odour sensor using the 
following procedure. 
When the air is clean (when there is no odour), disconnect the 
power plug and wait for 3 or more seconds. Connect the power 
plug once again, and start operation.

Odour comes from the air 
outlet.

Is a large amount of odour generated temporarily? (i.e., many 

 

people are smoking, grilling meat, etc.)

Operate the unit and the odour should gradually go away.

 

Î

Have you moved the unit from another room?

 

The original room may have an odour.

 

Î

Operate the unit for a while.

Are odours constantly generated in the room? (i.e., paint, new 

 

furniture, wall paper, sprays, cosmetics, chemicals, etc.)

As odour that is constantly generated can not be completely 

 

Î

removed, use the ventilation system in the room or operate the 
unit in a well-ventilated room for a while.

You may smell an odour as ozone particles are generated. 

 

The amount is negligible, so it does not harm your health.

01_EN_3P276413-2C.indd   24

01_EN_3P276413-2C.indd   24

9/27/2011   1:21:06 PM

9/27/2011   1:21:06 PM

Summary of Contents for MC70LBFVM






























Reviews: