![background image](http://html1.mh-extra.com/html/daikin/m08b055/m08b055_installation-manual_2460255006.webp)
Indoor Unit Installation (3)
1) Do not use spliced wires, strand wires, extension cords, or starburst connections, as they may cause overheating,
electrical shock, or fire. Follow all Local, and State electrical codes.
2) Do not use locally purchased electrical parts inside the product. (Do not overload the circuit by adding drain pump
or other electrical equipment to unit terminals.) Doing so may cause electric shock or fire.
3) When carrying out wiring connection, take care not to pull at the conduit.
WARNING
5.
When connecting to an HA system.
1) Remove the front grille. (2 screws)
2) Remove the electrical
wiring box. (3 screw)
3) Remove the metal plate
electrical wiring cover. (4 tabs)
4) Remove the resin plastic
electrical wiring cover. (2 tabs)
5) Attach the connection cord to the S21 connector and pull
the harness out through the notched part in the figure.
6) Replace the electrical wiring cover as it was, and pull the harness around, as shown in the figure.
6.
Drain piping.
1) Connect the drain hose,
as described right.
2) Remove the air filters
and pour some water
into the drain pan to
check the water flows
smoothly.
3) When drain hose requires extension, obtain
an extension hose commercially available.
Be sure to thermally insulate the indoor
section of the extension hose.
4) When connecting a rigid polyvinyl chloride pipe
(nominal diameter 1/2 inch (13mm)) directly to the drain
hose attached to the indoor unit as with embedded
piping work, use any commercially available drain
socket (nominal diameter 1/2 inch (13mm)) as a joint.
4.
Wiring.
1) Strip wire ends. (9/16 inch (15mm))
2) Match wire colours with terminal numbers on
indoor and outdoor unit’s terminal blocks and
firmly screw wires to the corresponding
terminals.
3) Connect the earth wires to the corresponding
terminals.
4) Pull wires to make sure that they are securely
latched up.
5) In case of connecting to an adapter system.
Run the remote controller cable and attach the S21 connector as the
illustration above.
6) Shape the wires so that the service lid fits securely, then close service lid.
3-3. Wall embedded piping.
Follow the instructions given under
1) Insert the drain hose to this depth so it won’t be
pulled out of the drain pipe.
Left-side, left-back, or left-bottom piping
The drain hose should
be inclined downward.
No trap is permitted.
Do not put the end
of the hose in water.
Indoor unit
drain hose
φ
11/16”
(
φ
18mm)
Extension drain hose
Heat insulation tube
(Field supply)
Drain hose supplied with
the indoor unit
Commercially available drain socket
(nominal diameter 1/2 inch (13mm))
Commercially available rigid
polyvinyl chloride pipe
(nominal diameter 1/2 inch (13mm))
φ
11/16”
(
φ
18mm)
3
2
1
1 2 3
L
1
L
2
When wire length exceeds
33ft (10m), use AWG14 wires.
Use AWG16 or AWG14 wire
for the Interconnecting wires.
Outdoor unit
Indoor
unit
Inner wall
Vinyl chloride
drain pipe
(VP-30)
Drain hose
1-15/16”
(50mm)
or more
Insert drain hose
to this depth so
it won’t be pulled
out of drain pipe.
Outer wall
Use the specified wire type.
Shape wires so that the service
lid will fit securely.
Electrical component box
Terminal block
1
2
3
Conduit
mounting
plate
Conduit
Lock nut
Back
6) Pull-around figure
Tab
Tab
HA cord
Notched part
Press
Tab
Tab
HA connector (S21)
Slide
Slide
Press
Press
Screws
Press
4) 5) Attach to the S21
connector and take the
harness out of the notched
part on the mounting.
3) Remove the metal
plate electrical
wiring cover.