2
c
odeS
& r
egulatIonS
This product is designed and manufactured to comply with
national codes. Installation in accordance with such codes
and/or prevailing local codes/regulations is the responsibility
of the installer. The manufacturer assumes no responsibility
for equipment installed in violation of any codes or regulations.
Rated performance is achieved after 72 hours of operation.
Rated performance is delivered at the specified airflow. See
outdoor unit specification sheet for split system models or
product specification sheet for packaged and light commercial
models. Specification sheets can be found at www.daikin
-
comfort.com for Daikin products. Within the website, please
select the products menu and then select the submenu for
the type of product to be installed, such as air conditioners,
to access a list of product pages that each contain links to
that model’s specification sheet.
the United States environmental Protection Agency
(ePA) has issued various regulations regarding the in-
troduction and disposal of refrigerants. failure to follow
these regulations may harm the environment and can
lead to the imposition of substantial fines.
Should you have any questions please contact our local EPA
office.
If replacing one of the component of the system, the system
must be manufacturer approved and Air Conditioning, Heating
and Refrigeration Institute (AHRI) matched.
note:
The installation of an inverter air conditioner with
unmatched system units will not allow for proper operation.
I
nverter
a/c
modelS
can
only
Be
matched
WIth
a
cape
**
and
chpe
** a-
coIl
. d
amage
reSultIng
from
operatIon
WIth
any
other
comBInatIon
IS
not
covered
By
our
WarrantIeS
.
notice
Outdoor inverter units are approved for operation above 0°F
in cooling mode with no additional kit necessary.
Damage resulting from operation of the unit in a structure
that is not complete (either as part of new construction or
renovation) is not covered by our warranties.
f
eatureS
This air conditioner is part of a system that uses inverter
technology to more efficiently remove heat and achieve the
target cooling setting. System may ONLY be installed using a
ComfortNet™ thermostat or a Daikin approved communicat-
ing thermostat. The ComfortNet system reduces the number
of required thermostat wires, provides additional setup fea-
tures and enhanced active diagnostics. Due to components
using inverter technology, the air conditioner will not function
properly if used with non-approved thermostat.
S
hould
uSe
a
d
aIkIn
approved
communIcatIng
thermoStat
.
notice
B
efore
I
nStallatIon
Precautions to remove packaging (corner guard)
•
Remove the packaging
(Corner guard) used to protect
the unit while carrying from the
right front part.
Follow the steps below to remove.
1. Remove the front plate screw.
2. Remove the packaging (Corner
guard).
3. Install the front plate screw to fix the front and top
plates.
About carrying
Hold the 2 handles at both sides as shown in the figure below
and move it slowly.
(Pay attention not to touch the fins at the back.)
Conner
Outdoor unit
Handles
(Front)
(Back)
Inlet holes
Exhaust grille
note:
Don’t place your fingers into the inlet holes of the
casing while moving the unit. Failure to do so may result in
deformation. Only hold the corner of the unit with your hands.
p
recautIonS
for
S
electIng
a
l
ocatIon
1. Choose a place solid enough to bear the weight and
vibration of the unit, where the operating sound will
not be amplified.
2. Choose a location where the hot air discharged
from the unit or the operating sound will not cause a
nuisance to the neighbours of the user.
3. Avoid places near a bedroom and the like, so that the
operating sound will cause no trouble.
4. There must be sufficient spaces for carrying the unit
into and out of the site.
5. There must be sufficient space for air passage and no
obstructions around the air inlet and the air outlet.
6. The site must be free from the possibility of flammable
gas leakage in a nearby place.
7. Do not install the air conditioner in the following
locations:
(a) Where a mineral oil mist or oil spray or vapor is produced,
for example, in a kitchen.
Plastic parts may deteriorate and fall off and thus may
result in water leakage.
(b) Where corrosive gas, such as sulfurous acid gas, is pro-
duced.
Corroding copper pipes or soldered parts may result in
refrigerant leakage.
(c) Near machinery emitting electromagnetic waves.
Electromagnetic waves may disturb the operation of the
control system and cause the unit to malfunction.
Packaging (pallet)
Front plate
Front plate
screw
Top
plate
Packaging (Corner guard)
