background image

English

3

See the included installation manuals on the VRV outdoor unit and the ceiling suspended cassette type 
indoor unit for details.

For the indoor unit connected to the BEV unit, cooling/heating cannot be switched over with the remote con-
troller.

When the cooling/heating free system is connected to the BS unit, a cooling/heating selection right is 
allowed.

When the ceiling suspended cassette type indoor unit and BEV unit are used for all indoor units, a separate 
“Cool/Heat SELECTOR” is needed to enable the cooling/heating switchover.

2-1 PRECAUTIONS

Do not install or operate the unit in rooms mentioned below.

Laden with mineral oil, or filled with oil vapor or spray like in kitchens. (Plastic parts may deteriorate which 
could eventually cause the unit to fall out of place, or could lead to leaks.)

Where corrosive gas like sulfurous gas exists. (Copper tubing and brazed spots may corrode, which 
could eventually lead to refrigerant leaks.)

Where exposed to combustible gas and where volatile flammable gas like thinner or gasoline is used. 
(Gas in the vicinity of the unit could ignite.)

Where machines can generate electromagnetic waves. (Control system may malfunction.)

Where the air contains high levels of salt such as that near the ocean and where voltage fluctuates 
greatly such as that in factories. 
Also in vehicles or vessels.

This unit, both indoor and outdoor, is suitable for installation in a commercial and light industrial environment.
If installed as a household appliance it could cause electromagnetic interference.

2-2 ACCESSORIES

Check  if the following accessories are included with your unit.

2-3 CONBINATION

Attach a BEV unit with the same capacity to the indoor unit.

Name

Clamp

Insulation for fitting

Sealing pad

(7) Gas piping 

connection piping

Quantity

9 pcs.

3 pcs.

3 pcs.

1 pc.

Shape

(1) 3 short pieces

(2) 6 long pieces

(3) For liquid piping × 2

(4) For gas piping × 1

(5)

Small × 2

(6)

× 1

Name

(8) Installation 

manual

(9) Nameplate

Quantity

1 pc.

1 pc.

Shape

BEV unit

BEVQ71MVE

BEVQ100MVE

BEVQ125MVE

Indoor unit

FXUQ71MV1

FXUQ100MV1

FXUQ125MV1

3P084604-2A_Eng.fm  Page 3  Wednesday, March 3, 2004  10:01 AM

Summary of Contents for BEVQ100MVE




















Reviews: