Daihen OTC WB-P400, Owner'S Manual

Page: 19 / 158

2-3
Chapter 2
P
ro
d
u
c
t S
p
e
c
ific
a
tio
n
a
n
d
C
o
n
fig
u
ra
tio
n
S
PECIFICATION
P
RODUCT
S
PECIFICATION AND
C
ONFIGURATION
C
HAPTER
2
2.1.2 Applicable welding method
This section explains the applicable welding method (shield gas/wire type/welding type) and wire
diameter.
Standard specification
WELDING
METHOD
GAS (*1) WIRE MATERIALS WIRE DIA. [in. (mm)] TRAVEL SPEED
Penetration
adjustment
DC
CO
2
MILD STEEL
030 / .035 / .040 /.045
(0.8/0.9/1.0/ 1.2)
(*2) (*3) Enable
MAG (20 % CO
2
)
(*1-1)
MILD STEEL
.030 / .035 / .040 /.045
(0.8/0.9/1.0/1.2)
(*2) (*3) Enable
MILD STEEL CORED .045 (1.2) STANDARD (*3) Enable
STAINLESS CORED .045 (1.2) STANDARD (*3) Enable
MIG (2 % O
2
)
(*1-2)
STAINLESS STEEL
.030 / .035 / .040 /.045
(0.8/0.9/1.0/1.2)
(*2) (*3) Enable
STAINLESS FERRITE
.030 / .035 / .040 /.045
(0.8/0.9/1.0/1.2)
(*2) (*3) Enable
MIG (100 % Ar)
(*1-3)
SOFT ALUMINUM .045 / 1/16 (1.2/1.6) (*2) (*3) -
HARD ALUMINUM .045 / 1/16 (1.2/1.6) (*2) (*3) -
Brazing CuSi
.030 / .035 / .045
(0.8/0.9/1.2)
(*2) (*3) -
Brazing CuAl
.030 / .035 / .045
(0.8/0.9/1.2)
(*2) (*3) -
DC
PULSE
MAG (20 % CO
2
)
(*1-1)
MILD STEEL
.030 / .035 / .040 /.045/
.052 (0.8/0.9/1.0/1.2/
1.4)
(*2) (*3) Enable
MIG (2 % O
2
)
(*1-2)
STAINLESS STEEL
.030 / .035 / 0.45
(0.8/0.9/1.2)
(*2) (*3) Enable
STAINLESS FERRITE
.030 / .035 / .045
(0.8/0.9/1.2)
(*2) (*3) Enable
MIG (100 % Ar)
(*1-3)
SOFT ALUMINUM .045 / 1/16 (1.2/1.6) (*2) (*3) -
HARD ALUMINUM .045 / 1/16 (1.2/1.6) (*2) (*3) -
Brazing CuSi
.030 / .035 / .045
(0.8/0.9/1.2)
(*2) (*3) -
Brazing CuAl
.030 / .035 / .045
(0.8/0.9/1.2)
(*2) (*3) -
INCONEL .035 / .045 (0.9/1.2) (*2) (*3) -
DC WAVE
PULSE
MAG (20 % CO
2
)
(*1-1)
MILD STEEL
.030 / .035 / .040 /.045 /
.052 (0.8/0.9/1.0/1.2/
1.4)
(*2) (*3) -
MIG (2 % O
2
)
(*1-2)
STAINLESS STEEL
.030 / .035 / .045
(0.8/0.9/1.2)
(*2) (*3) -
STAINLESS FERRITE
.030 / .035 / .045
(0.8/0.9/1.2)
(*2) (*3) -
MIG (100 % Ar)
(*1-3)
SOFT ALUMINUM .045 / 1/16 (1.2/1.6) (*2) (*3) -
HARD ALUMINUM .045 / 1/16 (1.2/1.6) (*2) (*3) -
*1: Note that the "collective" voltage adjustment may not meet the appropriate condition if a mixing gas other than those
with the following mixing ratios is used.
*1-1: MAG gas: Argon (Ar) 80 % + Carbon dioxide (CO
2
)20 %
*1-2: MIG gas (stainless steel): Argon(Ar) 98 % + Oxygen (O
2
)2 %
*1-3: MIG gas (Aluminum/Aluminum bronze/Silicon bronze): Argon (Ar)100 %
*2: Available for applications either of "STANDARD" or "HIGH".
*3: For "STANDARD" mode, the standard mode or extended cable mode (extended mode of power cable) is available.
( 6.7.2.1
-
F1: Standard/Extended cable mode)