background image

 

Foreword  V 

 

 

  Foreword 

General 

This  document  elaborates  on  structure,  installation  and  wiring  of  four-door  one-way  access 

controller. 

Safety Instructions 

The following categorized signal words with defined meaning might appear in the Manual. 

Signal Words

 

Meaning

 

 

Indicates a high potential hazard which, if not avoided, will result in 

death or serious injury. 

 

Indicates  a  medium  or  low  potential  hazard  which,  if  not  avoided, 

could result in slight or moderate injury. 

 

Indicates  a  potential  risk  which,  if  not  avoided,  could  result  in 

property  damage,  data  loss,  lower  performance,  or  unpredictable 

result. 

 

Provides methods to help you solve a problem or save you time. 

 

Provides additional information as the emphasis and supplement to 

the text. 

Privacy Protection Notice 

As the device user or data controller, you might collect personal data of others, such as face, 

fingerprints, car plate number, Email address, phone number, GPS and so on. You need to be 

in  compliance  with  the  local  privacy  protection  laws  and  regulations  to  protect  the  legitimate 

rights  and  interests  of  other  people  by  implementing  measures,  including  but  not  limited  to: 

providing  clear  and  visible  identification  to  inform  data  subject  the  existence  of  surveillance 

area and providing related contact. 

About the Manual 

 

The  Manual  is  for  reference  only.  If  there  is  inconsistency  between  the  Manual  and  the 

actual product, the actual product shall prevail. 

 

We are not liable for any loss caused by the operations that do not comply with the Manual. 

 

The  Manual  would  be  updated  according  to  the  latest  laws  and  regulations  of  related 

regions. For detailed information, see the paper User's Manual, CD-ROM, QR code or our 

official website. If there is inconsistency between paper User's Manual and the electronic 

version, the electronic version shall prevail. 

Summary of Contents for ASC1204B





































Reviews: