Dahua ASC1204B User Manual Download Page 8

Page: 8 / 36

Important Safeguards and Warnings VII

Important Safeguards and Warnings

The following description is the correct application method of the device. Please read the

manual carefully before use, in order to prevent danger and property loss. Strictly conform to

the manual during application and keep it properly after reading.

Operating Requirement



Please don’t place and install the device in an area exposed to direct sunlight or near heat
generating device.



Please don’t install the device in a humid, dusty or fuliginous area.



Please keep its horizontal installation, or install it at stable places, and prevent it from

falling.



Please don’t drip or splash liquids onto the device; don’t put on the device anything filled
with liquids, in order to prevent liquids from flowing into the device.



Please install the device at well-

ventilated places; don’t block its ventilation opening.



Use the device only within rated input and output range.



Please don’t dismantle the device arbitrarily.



Please transport, use and store the device within allowed humidity and temperature range.

Power Requirement



Please make sure to use batteries according to requirements; otherwise, it may result in

fire, explosion or burning risks of batteries!



To replace batteries, only the same type of batteries can be used!



The product shall use electric cables (power cables) recommended by this area, which

shall be used within its rated specification!



Please use standard power adapter matched with the device. Otherwise, the user shall

undertake resulting personnel injury or device damage.



Please use power supply that meets SELV (safety extra low voltage) requirements, and

supply power with rated voltage that conforms to Limited Power Source in IEC60950-1. For

specific power supply requirements, please refer to device labels.



Products with category I structure shall be connected to grid power output socket, which is

equipped with protective grounding.



Appliance coupler is a disconnecting device. During normal use, please keep an angle that

facilitates operation.

Summary of Contents for ASC1204B





































Search results

Summary of Contents for ASC1204B

Reviews:

Related manuals for ASC1204B

Brands by name

Popular brands

Dahua ASC1204B, User Manual

Search results

Summary of Contents for ASC1204B

Reviews:

Related manuals for ASC1204B

Brands by name

Popular brands