•
The engine exhaust suddenly turns dark grey or black.
•
The fault indicating light is illuminated.
8. SHUT THE GAS GENERATORDOWN
circuit breaker to the “OFF” position and depress the reset key. This will automatically shut the
engine and generator down.
The generator don’t need any close switch if connected with ATS system.
9. STORAGE OF THE GENERATOR
Long time storage of the Genset.
1. Remove all dirty of the genset, if it needs to storage for long time
2. Drain the coolant of the engine
3. Ensure engine is in good technical condition, keep the surface clean
4. Remove all of the spark plugs, inlet about 30 g engine oil, turn the crankshaft about 20 turns, and
then reinstall the spark plug.
5. Use dewatering Vaseline (heating 100-200ºC) to wipe on the surface of the contactor and unpain-
ted metal surfaces.
6. Add lubrication oil on each lubrication points.
7. Use protection materials (like Canvas. Waterproof cloth or Oil paper) cover the engine to keep it
dust-free.
8. Keep the room clean ,warm, shady and the temperature should better be 5-35 , the best relative
temperature should be better at 40-70%
9. Check all of the nuts and screws, fasten the loosen one and sealing the genset while shut down
the general gas inlet valve, and push the emergency button.
10. Remove the battery positive pole connect line, and get out the battery, then keep the battery in
dark and dry place. And recharge it slowly every three months.
11. Sealing it with the sealing rubber, to avoid the dust get in to the gas pipe
12. Cover the generator with the dustproof cover, and keep it in the dry and clean place;
and explosive materials.
Start after long time’s storage
1. Remove the dust-proof oil
2. Remove the spark plug, and inlet about 30g engine oil.
3. Add coolant.
4. Add engine oil.
5. Check the wires and pipes connection.
6. Check the leakage of the gas pipe.
7. Run the engine to check it is normal or not.
8. Add lubrication to all of the necessary places.
9. Tighten the engine oil pump belt
10. Check the electrical parts working condition
11. Before start the generator, check the whole generator, including the nuts and screws.
•
The engine exhaust suddenly turns dark grey or black.
•
The fault indicating light is illuminated.
8. SHUT THE GAS GENERATORDOWN
circuit breaker to the “OFF” position and depress the reset key. This will automatically shut the
engine and generator down.
The generator don’t need any close switch if connected with ATS system.
9. STORAGE OF THE GENERATOR
Long time storage of the Genset.
1. Remove all dirty of the genset, if it needs to storage for long time
2. Drain the coolant of the engine
3. Ensure engine is in good technical condition, keep the surface clean
4. Remove all of the spark plugs, inlet about 30 g engine oil, turn the crankshaft about 20 turns, and
then reinstall the spark plug.
5. Use dewatering Vaseline (heating 100-200ºC) to wipe on the surface of the contactor and unpain-
ted metal surfaces.
6. Add lubrication oil on each lubrication points.
7. Use protection materials (like Canvas. Waterproof cloth or Oil paper) cover the engine to keep it
dust-free.
8. Keep the room clean ,warm, shady and the temperature should better be 5-35 , the best relative
temperature should be better at 40-70%
9. Check all of the nuts and screws, fasten the loosen one and sealing the genset while shut down
the general gas inlet valve, and push the emergency button.
10. Remove the battery positive pole connect line, and get out the battery, then keep the battery in
dark and dry place. And recharge it slowly every three months.
11. Sealing it with the sealing rubber, to avoid the dust get in to the gas pipe
12. Cover the generator with the dustproof cover, and keep it in the dry and clean place;
and explosive materials.
Start after long time’s storage
1. Remove the dust-proof oil
2. Remove the spark plug, and inlet about 30g engine oil.
3. Add coolant.
4. Add engine oil.
5. Check the wires and pipes connection.
6. Check the leakage of the gas pipe.
7. Run the engine to check it is normal or not.
8. Add lubrication to all of the necessary places.
9. Tighten the engine oil pump belt
10. Check the electrical parts working condition
11. Before start the generator, check the whole generator, including the nuts and screws.
•
The engine exhaust suddenly turns dark grey or black.
•
The fault indicating light is illuminated.
8. SHUT THE GAS GENERATORDOWN
circuit breaker to the “OFF” position and depress the reset key. This will automatically shut the
engine and generator down.
The generator don’t need any close switch if connected with ATS system.
9. STORAGE OF THE GENERATOR
Long time storage of the Genset.
1. Remove all dirty of the genset, if it needs to storage for long time
2. Drain the coolant of the engine
3. Ensure engine is in good technical condition, keep the surface clean
4. Remove all of the spark plugs, inlet about 30 g engine oil, turn the crankshaft about 20 turns, and
then reinstall the spark plug.
5. Use dewatering Vaseline (heating 100-200ºC) to wipe on the surface of the contactor and unpain-
ted metal surfaces.
6. Add lubrication oil on each lubrication points.
7. Use protection materials (like Canvas. Waterproof cloth or Oil paper) cover the engine to keep it
dust-free.
8. Keep the room clean ,warm, shady and the temperature should better be 5-35 , the best relative
temperature should be better at 40-70%
9. Check all of the nuts and screws, fasten the loosen one and sealing the genset while shut down
the general gas inlet valve, and push the emergency button.
10. Remove the battery positive pole connect line, and get out the battery, then keep the battery in
dark and dry place. And recharge it slowly every three months.
11. Sealing it with the sealing rubber, to avoid the dust get in to the gas pipe
12. Cover the generator with the dustproof cover, and keep it in the dry and clean place;
and explosive materials.
Start after long time’s storage
1. Remove the dust-proof oil
2. Remove the spark plug, and inlet about 30g engine oil.
3. Add coolant.
4. Add engine oil.
5. Check the wires and pipes connection.
6. Check the leakage of the gas pipe.
7. Run the engine to check it is normal or not.
8. Add lubrication to all of the necessary places.
9. Tighten the engine oil pump belt
10. Check the electrical parts working condition
11. Before start the generator, check the whole generator, including the nuts and screws.
17
•
The engine exhaust suddenly turns dark grey or black.
•
The fault indicating light is illuminated.
8. SHUT THE GAS GENERATORDOWN
circuit breaker to the “OFF” position and depress the reset key. This will automatically shut the
engine and generator down.
The generator don’t need any close switch if connected with ATS system.
9. STORAGE OF THE GENERATOR
Long time storage of the Genset.
1. Remove all dirty of the genset, if it needs to storage for long time
2. Drain the coolant of the engine
3. Ensure engine is in good technical condition, keep the surface clean
4. Remove all of the spark plugs, inlet about 30 g engine oil, turn the crankshaft about 20 turns, and
then reinstall the spark plug.
5. Use dewatering Vaseline (heating 100-200ºC) to wipe on the surface of the contactor and unpain-
ted metal surfaces.
6. Add lubrication oil on each lubrication points.
7. Use protection materials (like Canvas. Waterproof cloth or Oil paper) cover the engine to keep it
dust-free.
8. Keep the room clean ,warm, shady and the temperature should better be 5-35 , the best relative
temperature should be better at 40-70%
9. Check all of the nuts and screws, fasten the loosen one and sealing the genset while shut down
the general gas inlet valve, and push the emergency button.
10. Remove the battery positive pole connect line, and get out the battery, then keep the battery in
dark and dry place. And recharge it slowly every three months.
11. Sealing it with the sealing rubber, to avoid the dust get in to the gas pipe
12. Cover the generator with the dustproof cover, and keep it in the dry and clean place;
and explosive materials.
Start after long time’s storage
1. Remove the dust-proof oil
2. Remove the spark plug, and inlet about 30g engine oil.
3. Add coolant.
4. Add engine oil.
5. Check the wires and pipes connection.
6. Check the leakage of the gas pipe.
7. Run the engine to check it is normal or not.
8. Add lubrication to all of the necessary places.
9. Tighten the engine oil pump belt
10. Check the electrical parts working condition
11. Before start the generator, check the whole generator, including the nuts and screws.
•
The engine exhaust suddenly turns dark grey or black.
•
The fault indicating light is illuminated.
8. SHUT THE GAS GENERATORDOWN
circuit breaker to the “OFF” position and depress the reset key. This will automatically shut the
engine and generator down.
The generator don’t need any close switch if connected with ATS system.
9. STORAGE OF THE GENERATOR
Long time storage of the Genset.
1. Remove all dirty of the genset, if it needs to storage for long time
2. Drain the coolant of the engine
3. Ensure engine is in good technical condition, keep the surface clean
4. Remove all of the spark plugs, inlet about 30 g engine oil, turn the crankshaft about 20 turns, and
then reinstall the spark plug.
5. Use dewatering Vaseline (heating 100-200ºC) to wipe on the surface of the contactor and unpain-
ted metal surfaces.
6. Add lubrication oil on each lubrication points.
7. Use protection materials (like Canvas. Waterproof cloth or Oil paper) cover the engine to keep it
dust-free.
8. Keep the room clean ,warm, shady and the temperature should better be 5-35 , the best relative
temperature should be better at 40-70%
9. Check all of the nuts and screws, fasten the loosen one and sealing the genset while shut down
the general gas inlet valve, and push the emergency button.
10. Remove the battery positive pole connect line, and get out the battery, then keep the battery in
dark and dry place. And recharge it slowly every three months.
11. Sealing it with the sealing rubber, to avoid the dust get in to the gas pipe
12. Cover the generator with the dustproof cover, and keep it in the dry and clean place;
and explosive materials.
Start after long time’s storage
1. Remove the dust-proof oil
2. Remove the spark plug, and inlet about 30g engine oil.
3. Add coolant.
4. Add engine oil.
5. Check the wires and pipes connection.
6. Check the leakage of the gas pipe.
7. Run the engine to check it is normal or not.
8. Add lubrication to all of the necessary places.
9. Tighten the engine oil pump belt
10. Check the electrical parts working condition
11. Before start the generator, check the whole generator, including the nuts and screws.
•
The engine exhaust suddenly turns dark grey or black.
•
The fault indicating light is illuminated.
8. SHUT THE GAS GENERATORDOWN
circuit breaker to the “OFF” position and depress the reset key. This will automatically shut the
engine and generator down.
The generator don’t need any close switch if connected with ATS system.
9. STORAGE OF THE GENERATOR
Long time storage of the Genset.
1. Remove all dirty of the genset, if it needs to storage for long time
2. Drain the coolant of the engine
3. Ensure engine is in good technical condition, keep the surface clean
4. Remove all of the spark plugs, inlet about 30 g engine oil, turn the crankshaft about 20 turns, and
then reinstall the spark plug.
5. Use dewatering Vaseline (heating 100-200ºC) to wipe on the surface of the contactor and unpain-
ted metal surfaces.
6. Add lubrication oil on each lubrication points.
7. Use protection materials (like Canvas. Waterproof cloth or Oil paper) cover the engine to keep it
dust-free.
8. Keep the room clean ,warm, shady and the temperature should better be 5-35 , the best relative
temperature should be better at 40-70%
9. Check all of the nuts and screws, fasten the loosen one and sealing the genset while shut down
the general gas inlet valve, and push the emergency button.
10. Remove the battery positive pole connect line, and get out the battery, then keep the battery in
dark and dry place. And recharge it slowly every three months.
11. Sealing it with the sealing rubber, to avoid the dust get in to the gas pipe
12. Cover the generator with the dustproof cover, and keep it in the dry and clean place;
and explosive materials.
Start after long time’s storage
1. Remove the dust-proof oil
2. Remove the spark plug, and inlet about 30g engine oil.
3. Add coolant.
4. Add engine oil.
5. Check the wires and pipes connection.
6. Check the leakage of the gas pipe.
7. Run the engine to check it is normal or not.
8. Add lubrication to all of the necessary places.
9. Tighten the engine oil pump belt
10. Check the electrical parts working condition
11. Before start the generator, check the whole generator, including the nuts and screws.
Summary of Contents for DAPD17REQ-EC
