Daewoo DAPD17REQ-EC, User Manual

Page: 10 / 50

Use
:
When starting manually, always start the generator before placing the circuit breaker in the ON
position. Likewise, when operating manually, place the circuit breaker in the OFF position before
shutting the generator down.
5. PRESTART PREPARATION
All necessary installation and maintenance shall be conducted by authorized personnel.
1. Engine Oil.
Fill, if necessary, with the recommended viscosity and grade of oil. Or it cause damage on engine.
Use the following recommended or similar engine oil.
• Put the funnel at engine oil inlet, keep not leans.
•
• Check the oil gauge, the oil level should keep at top center of two line.
2. Coolant
The cooling water should be the clean soft water, such as rain and snow water. As for well water,
spring and tap water, they must be boiled and deposited or processed with chemical method. It is
necessary to do the water softening work well for some areas which contain a lot of salt and alkali.
cause fault. If you don’t use or maintain fuel, lubricant, coolant and relative systems of genset well, it
must cause accelerate of fray and shorten the working life of machine or cause fault. So the users
must pay much attention to them.
recommended coolant after installation of gensets.
Fill up radiator with the coolant, the unit ran around 5 minutes, pour coolant again into radiator.
Add some coolant to reservoir and make sure the level is in the middle of “LOW” and “FULL”.
Use
:
When starting manually, always start the generator before placing the circuit breaker in the ON
position. Likewise, when operating manually, place the circuit breaker in the OFF position before
shutting the generator down.
5. PRESTART PREPARATION
All necessary installation and maintenance shall be conducted by authorized personnel.
1. Engine Oil.
Fill, if necessary, with the recommended viscosity and grade of oil. Or it cause damage on engine.
Use the following recommended or similar engine oil.
• Put the funnel at engine oil inlet, keep not leans.
•
• Check the oil gauge, the oil level should keep at top center of two line.
2. Coolant
The cooling water should be the clean soft water, such as rain and snow water. As for well water,
spring and tap water, they must be boiled and deposited or processed with chemical method. It is
necessary to do the water softening work well for some areas which contain a lot of salt and alkali.
cause fault. If you don’t use or maintain fuel, lubricant, coolant and relative systems of genset well, it
must cause accelerate of fray and shorten the working life of machine or cause fault. So the users
must pay much attention to them.
recommended coolant after installation of gensets.
Fill up radiator with the coolant, the unit ran around 5 minutes, pour coolant again into radiator.
Add some coolant to reservoir and make sure the level is in the middle of “LOW” and “FULL”.
EN
10
Use
:
When starting manually, always start the generator before placing the circuit breaker in the ON
position. Likewise, when operating manually, place the circuit breaker in the OFF position before
shutting the generator down.
5. PRESTART PREPARATION
All necessary installation and maintenance shall be conducted by authorized personnel.
1. Engine Oil.
Fill, if necessary, with the recommended viscosity and grade of oil. Or it cause damage on engine.
Use the following recommended or similar engine oil.
• Put the funnel at engine oil inlet, keep not leans.
•
• Check the oil gauge, the oil level should keep at top center of two line.
2. Coolant
The cooling water should be the clean soft water, such as rain and snow water. As for well water,
spring and tap water, they must be boiled and deposited or processed with chemical method. It is
necessary to do the water softening work well for some areas which contain a lot of salt and alkali.
cause fault. If you don’t use or maintain fuel, lubricant, coolant and relative systems of genset well, it
must cause accelerate of fray and shorten the working life of machine or cause fault. So the users
must pay much attention to them.
recommended coolant after installation of gensets.
Fill up radiator with the coolant, the unit ran around 5 minutes, pour coolant again into radiator.
Add some coolant to reservoir and make sure the level is in the middle of “LOW” and “FULL”.
Oil grade (optional)
5W/30 10W/30
10W/30 15W/40
15W/40
Ambient temperature
Use
:
When starting manually, always start the generator before placing the circuit breaker in the ON
position. Likewise, when operating manually, place the circuit breaker in the OFF position before
shutting the generator down.
5. PRESTART PREPARATION
All necessary installation and maintenance shall be conducted by authorized personnel.
1. Engine Oil.
Fill, if necessary, with the recommended viscosity and grade of oil. Or it cause damage on engine.
Use the following recommended or similar engine oil.
• Put the funnel at engine oil inlet, keep not leans.
•
• Check the oil gauge, the oil level should keep at top center of two line.
2. Coolant
The cooling water should be the clean soft water, such as rain and snow water. As for well water,
spring and tap water, they must be boiled and deposited or processed with chemical method. It is
necessary to do the water softening work well for some areas which contain a lot of salt and alkali.
cause fault. If you don’t use or maintain fuel, lubricant, coolant and relative systems of genset well, it
must cause accelerate of fray and shorten the working life of machine or cause fault. So the users
must pay much attention to them.
recommended coolant after installation of gensets.
Fill up radiator with the coolant, the unit ran around 5 minutes, pour coolant again into radiator.
Add some coolant to reservoir and make sure the level is in the middle of “LOW” and “FULL”.
Use
:
When starting manually, always start the generator before placing the circuit breaker in the ON
position. Likewise, when operating manually, place the circuit breaker in the OFF position before
shutting the generator down.
5. PRESTART PREPARATION
All necessary installation and maintenance shall be conducted by authorized personnel.
1. Engine Oil.
Fill, if necessary, with the recommended viscosity and grade of oil. Or it cause damage on engine.
Use the following recommended or similar engine oil.
• Put the funnel at engine oil inlet, keep not leans.
•
• Check the oil gauge, the oil level should keep at top center of two line.
2. Coolant
The cooling water should be the clean soft water, such as rain and snow water. As for well water,
spring and tap water, they must be boiled and deposited or processed with chemical method. It is
necessary to do the water softening work well for some areas which contain a lot of salt and alkali.
cause fault. If you don’t use or maintain fuel, lubricant, coolant and relative systems of genset well, it
must cause accelerate of fray and shorten the working life of machine or cause fault. So the users
must pay much attention to them.
recommended coolant after installation of gensets.
Fill up radiator with the coolant, the unit ran around 5 minutes, pour coolant again into radiator.
Add some coolant to reservoir and make sure the level is in the middle of “LOW” and “FULL”.
Use
:
When starting manually, always start the generator before placing the circuit breaker in the ON
position. Likewise, when operating manually, place the circuit breaker in the OFF position before
shutting the generator down.
5. PRESTART PREPARATION
All necessary installation and maintenance shall be conducted by authorized personnel.
1. Engine Oil.
Fill, if necessary, with the recommended viscosity and grade of oil. Or it cause damage on engine.
Use the following recommended or similar engine oil.
• Put the funnel at engine oil inlet, keep not leans.
•
• Check the oil gauge, the oil level should keep at top center of two line.
2. Coolant
The cooling water should be the clean soft water, such as rain and snow water. As for well water,
spring and tap water, they must be boiled and deposited or processed with chemical method. It is
necessary to do the water softening work well for some areas which contain a lot of salt and alkali.
cause fault. If you don’t use or maintain fuel, lubricant, coolant and relative systems of genset well, it
must cause accelerate of fray and shorten the working life of machine or cause fault. So the users
must pay much attention to them.
recommended coolant after installation of gensets.
Fill up radiator with the coolant, the unit ran around 5 minutes, pour coolant again into radiator.
Add some coolant to reservoir and make sure the level is in the middle of “LOW” and “FULL”.