Transmission Medium
1000BASE-SX(850nm)
Multi-mode optical fiber
1000BASE-LX(1310nm)
Single-mode optical fiber
1000BASE-LH40(1310nm)
Single-mode optical fiber
1000BASE-ZX(1550nm)
Single-mode optical fiber
100BASE-FX(1310nm)
Multi-mode or single-mode optical fiber
100BASE-FX(1550nm)
Single-mode optical fiber
10/100/1000BASE-T
Cat-5 UTP
LED
Status, Link/ACT
Hot Swapping
Supported
Power Consumption
<121W+15.4xN (N indicates the number of PoE ports being used, N<=48)
EMC Standards
GB9254-2008
Safety Standards
GB4943-2011
Operating
Temperature
0 to 40°C
Storage Temperature
-40 to 70°C
Operating Humidity
10% to 90% RH (non-condensing)
Weight
Net weight: 3.8 kg
Dimensions
(L x W x H)
436 mm x 346 mm x 45 mm
The last four ports of the M8600P-48GT/4SFP-EC service module are fiber/copper combo ports. Each SFP port
corresponds to one combo 10/100/1000BASE-T port, and only one port can be used at a time, while the other is
unavailable. The automatic MDI/MDI-X identification of the 10/100/1000M copper ports takes effect only when
auto-negotiation is enabled.
The M8600P-48GT/4SFP-EC supports 1000BASE-X and 100BASE-FX. You need to configure the ports as the
desired operating modes according to the Configuration Manual of Ruijie Networks.
The M8600P-48GT/4FP-EC supports the PoE function, with a maximum of 15.4W of power output per port. If the
host is configured with the M8600P-48GT/4SFP-EC line card, the power consumption should be calculated
according to the number of powered devices (PDs) attached and the power consumed by each PD.
The M8600P-48GT/4SFP is hot swappable. You need to perform the following operations before hot swapping:
1. Disconnect all cables connected to the PoE;
2. In the PoE mode, hold the Mode button for over three seconds until all the LEDs on the line card go off;
3. Configure the pull-out operation through software commands.(For relevant software configuration commands,
refer to the corresponding software description.)
M8600-24GT/12SFP-EC
Module Appearance
Figure 1-40 Appearance of the M8600-24GT/12SFP-EC
External Interface
The M8600-24GT/12SFP-EC provides twelve 10/100/1000BASE-T RJ45 ports and twelve fiber/copper combo ports. The
SFP ports support the rate of 100/1000 Mbps, the RJ45 ports support auto-negotiation at 10/100/1000 Mbps and the SFP
optical modules support hot swapping.
LED
Sign
Description
Detailed information
Status
System LED
OFF: The module is not powered on.
Red: The module is faulty.
Blinking green: The module is initializing. If it keeps blinking, the
module may be faulty.
Solid green: The module has finished initialization and can perform
switching well.
Summary of Contents for RG-S8614
