DXS-3600 Series 10GbE Layer 2/3 Switch CLI Reference Guide
123
7-71 show ip bgp vrf
This command is used to display entries in the BGP routing table in VRF address family.
show ip bgp vrf
VRF-NAME
[{
IP-ADDRESS
|
NETWORK-ADDRESS
[longer-prefixes] | label}]
Parameters
Display Parameters
Description
BGP Local Router ID
The router identifier of the local BGP router.
Status codes
Status of the table entry displayed at the beginning of each line. It can be one or
more of the following values:
s—The table entry is suppressed.
d—The table entry is damped.
h—The table entry is damped and has been withdrawn by the neighbor.
*—The table entry is valid.
>—The table entry is the best entry to use for that network.
i—The table entry was learned via an internal BGP (iBGP) session.
Origin codes
Origin of the table entry displayed at the end of each line. It can be one of the
following values:
i—Entry originated from an Interior Gateway Protocol (IGP) and was advertised
with a
network router configuration
command.
e—Entry originated from an Exterior Gateway Protocol (EGP).
?—Origin of the path is not clear. Usually, this is a router that is redistributed into
BGP from an IGP.
IP Address/Netmask
IP prefix with its mask length of the entry.
Gateway
IP address of the next router that is used when forwarding a packet to the destination
network. An entry of 0.0.0.0 indicates that the router has some non-BGP routes to
this network.
Metric
If shown, this is the value of the inter-autonomous system metric. This field is
frequently not used.
LocPrf
Local preference value as set with the
set local-preference route-map
configuration command. The default value is 100.
Weight
Weight of the route as set via autonomous system filters.
Route Distinguisher
Specify the route distinguisher of the following routes.
default for vrf
Specify the VRF which The route distinguisher is default for.
VPN route(s)
Specify that the following routes are learned from PEs.
Path
Autonomous system paths to the destination network.
From
Specify the origin of this prefix.
In label
Specify the label which would be assigned to other routes that origin from other PE.
Out label
Specify the label which get form other PE neighbor.
Self Peer
Specify that the route is originated from local.
no
Specify this prefix does not have label of this direction.
vrf
VRF-NAME
(Optional) Specifies the VRF name.
IP-ADDRESS
(Optional) Specifies the IP address entered to filter the output to display only a
particular host or network in the BGP routing table.
NETWORK-ADDRESS
(Optional) Specifies to display the route matching the network address.
longer-prefixes
(Optional) Displays the specified route and all more specific routes.
label
(Optional) Specifies to display the BGP private labels of the routes, which are
assigned from MPLS.
Summary of Contents for DXS-3600-16S
