DWS-3160 Series Gigabit Ethernet Unified Switch CLI Reference Guide
824
will use.
<int 0-65535>
- Enter the custom source Layer 4 port number used here. This value
must be between 0 and 65535.
dst_layer4_port
- Specifies the destination Layer 4 port match condition for the IP ACL rule.
domain
- Specifies that the destination Layer 4 port match condition will use to port
number of the service called Domain.
echo
- Specifies that the destination Layer 4 port match condition will use to port number
of the service called Echo.
ftp
- Specifies that the destination Layer 4 port match condition will use to port number of
the service called FTP.
ftpdata
- Specifies that the destination Layer 4 port match condition will use to port number
of the service called FTP Data.
http
- Specifies that the destination Layer 4 port match condition will use to port number of
the service called HTTP.
smtp
- Specifies that the destination Layer 4 port match condition will use to port number
of the service called SMTP.
snmp
- Specifies that the destination Layer 4 port match condition will use to port number
of the service called SNMP.
telnet
- Specifies that the destination Layer 4 port match condition will use to port number
of the service called TELNET.
tftp
- Specifies that the destination Layer 4 port match condition will use to port number of
the service called TFTP.
other
- Specifies to use a custom port number that the destination Layer 4 port match
condition will use.
<int 0-65535>
- Enter the custom destination Layer 4 port number used here. This
value must be between 0 and 65535.
protocol
- Specifies the protocol to filter for an extended IP ACL rule, identified by number.
The protocol number is a standard value assigned by IANA and is interpreted as an integer
from 1 to 255. You can use the protocol number or you Specifies a protocol keyword.
ip
- Specifies that the protocol, used to filter for an extended IP ACL rule, is IP.
icmp
- Specifies that the protocol, used to filter for an extended IP ACL rule, is ICMP.
igmp
- Specifies that the protocol, used to filter for an extended IP ACL rule, is IGMP.
tcp
- Specifies that the protocol, used to filter for an extended IP ACL rule, is TCP.
udp
- Specifies that the protocol, used to filter for an extended IP ACL rule, is UDP.
other
- Specifies a custom protocol number to use in the extended IP ACL rule.
<int 1-255>
- Enter the custom protocol number, used to filter for an extended IP ACL
rule, here. This value must be between 1 and 255.
service
- Specifies the Service Type match condition for the extended IP ACL rule.
ip_precedence
- Specifies the IP precedence field in a packet that is defined as the high-
order three bits of the Service Type octet in the IP header.
<value 0-7>
- Enter the IP precedence value used here. This value must be between 0 and
7.
ip_tos
- Specifies the IP ToS field in a packet that is defined as all eight bits of the Service
Type octet in the IP header. The ToS Bits value is a two-digit hexadecimal number from 00
to ff. The TOS Mask value is a two-digit hexadecimal number from 0x00 to 0xff,
representing an inverted mask. The zero-valued bits in the ToS Mask denote the bit
positions in the ToS bits value that are used for comparison against the IP ToS field of a
packet.
tos_bit
- Specifies the ToS Bit value.
<hex 0x00-0xff>
- Enter the ToS Bit value used here. This value must be between 0x00
and 0xff.
tos_mask
- Specifies the ToS Mask value.
<hex 0x00-0xff>
- Enter the ToS Mask value used here. This value must be between
0x00 and 0xff.
ip_dscp
- Specifies the IP DiffServ Code Point (DSCP) field. The DSCP is defined as the
high-order six bits of the Service Type octet in the IP header. The IP DSCP is configured
by a possible selection of one of the DSCP keywords or a numerical values.
af11
- Specifies that the IP DiffServ Code Point value will be set as 'af11'.
af12
- Specifies that the IP DiffServ Code Point value will be set as 'af12'.
af13
- Specifies that the IP DiffServ Code Point value will be set as 'af13'.
